Replacing PCCB with steel rotors?
#16
Thank you! I will get a second opinion as to whether they need replacement or not just in case, but my main question is: for my intended use: daily driver with 6+/- auto crosses a year, if I go with original PCCB, will I destroy them in a year, or only hard tracking does that? ...is auto cross as hard on PCCB as real track? I've never been on a track, have no basis for comparison...thank you!
#17
Thank you Elliot, the car was not CPO, but PPI mechanic did not mention anything about rotors. Car arrived here in Los Angeles, this morning, I took it to local mechanic to have her looked over and that is where the issue was brought up. It sounds like I should really get a second opinion just in case. We did not measure the rotors, just visually inspected and I was told the rear ones are goners...thank you! Here are PPI pics of pads...I know it does not do much to address the rotors...but still. I think you can see wear indicator on one of the pics, right in line with valve stem...
Is this a ware indicator inline with valve stem?
Elliot
Is this a ware indicator inline with valve stem?
Elliot
from these photos I don't see any damage or wear. I don't think he knew what he was looking at.
You can certainly do Auto X or drivers ed on PCCBs with out worry and you will be amazed how much bite they have..
The reason track junkies use steel is they consider them a wear item and want to buy new ceramics even if they last 10 times longer.
PCCBs on on the 918 spyder just make a point.
Elliot
#18
from these photos I don't see any damage or wear. I don't think he knew what he was looking at.
You can certainly do Auto X or drivers ed on PCCBs with out worry and you will be amazed how much bite they have..
The reason track junkies use steel is they consider them a wear item and want to buy new ceramics even if they last 10 times longer.
PCCBs on on the 918 spyder just make a point.
Elliot
You can certainly do Auto X or drivers ed on PCCBs with out worry and you will be amazed how much bite they have..
The reason track junkies use steel is they consider them a wear item and want to buy new ceramics even if they last 10 times longer.
PCCBs on on the 918 spyder just make a point.
Elliot
#20
I am hopelessly confused now :-). But it does give thickness measurements on the rotors themselves...will measure over the weekend and see if we are within those limits...will also read the manual over the weekend...just afraid that wherever I go someone will see a $10,000 job and won't give me straight scoop as to whether they are good or not...or maybe I jut being overly paranoid...
#22
#24
Wear rings are showing on the rear. Visible is not too bad. At this point I would disassemble and weigh. There is a spec they need to weigh in at, if they are lighter than spec they need to be tossed. My rears look like that as well.
Used sets of PCCB rotors are always available on RL. Most of them are reasonable. I myself have purchased one or two sets here.
Used sets of PCCB rotors are always available on RL. Most of them are reasonable. I myself have purchased one or two sets here.
#25
Thank you! For sure I'll be getting a second opinion...just got a dealer quote for the rotors...needless to say that is not going to happen...I am secretly hoping that you guys are right and I am good to go...but even this potentially big expense can't seem to hurt my mood. I LOVE the car...yesterday as I was walking through parking lot toward it, I caught myself giggling...just awesome!!!
#26
Wear rings are showing on the rear. Visible is not too bad. At this point I would disassemble and weigh. There is a spec they need to weigh in at, if they are lighter than spec they need to be tossed. My rears look like that as well.
Used sets of PCCB rotors are always available on RL. Most of them are reasonable. I myself have purchased one or two sets here.
Used sets of PCCB rotors are always available on RL. Most of them are reasonable. I myself have purchased one or two sets here.
#27
Yes.
Only real way to know if the rotors are timed out is to disassemble and weigh. There is a PDF floating around here in RL concerning this. The fibers burn out from the outside surface through the rotor. If enough fibers burn up, the rotor loses too much mass. Some people base the rotor life on surface porosity (rougher the texture, less time it has before R&R).
Hope that helps.
Only real way to know if the rotors are timed out is to disassemble and weigh. There is a PDF floating around here in RL concerning this. The fibers burn out from the outside surface through the rotor. If enough fibers burn up, the rotor loses too much mass. Some people base the rotor life on surface porosity (rougher the texture, less time it has before R&R).
Hope that helps.
#28
Yes.
Only real way to know if the rotors are timed out is to disassemble and weigh. There is a PDF floating around here in RL concerning this. The fibers burn out from the outside surface through the rotor. If enough fibers burn up, the rotor loses too much mass. Some people base the rotor life on surface porosity (rougher the texture, less time it has before R&R).
Hope that helps.
Only real way to know if the rotors are timed out is to disassemble and weigh. There is a PDF floating around here in RL concerning this. The fibers burn out from the outside surface through the rotor. If enough fibers burn up, the rotor loses too much mass. Some people base the rotor life on surface porosity (rougher the texture, less time it has before R&R).
Hope that helps.
#29
congrats on one beast of car. I just got a 2011 Turbo S coupe also. speed yellow. congrats again.
my car had 13,500 miles on it...I took it in for its 4 year/30k mile maintenance and they went over the whole car, all they recommended was a brake fluid flush and said my rotors/pads were all fine..
car had to have been tracked, but I would do what the other guys said and have it seen at a reputable Porsche dealer, the PCCB rotors have a different appearance as if they are cracked all over
my car had 13,500 miles on it...I took it in for its 4 year/30k mile maintenance and they went over the whole car, all they recommended was a brake fluid flush and said my rotors/pads were all fine..
car had to have been tracked, but I would do what the other guys said and have it seen at a reputable Porsche dealer, the PCCB rotors have a different appearance as if they are cracked all over
#30
congrats on one beast of car. I just got a 2011 Turbo S coupe also. speed yellow. congrats again.
my car had 13,500 miles on it...I took it in for its 4 year/30k mile maintenance and they went over the whole car, all they recommended was a brake fluid flush and said my rotors/pads were all fine..
car had to have been tracked, but I would do what the other guys said and have it seen at a reputable Porsche dealer, the PCCB rotors have a different appearance as if they are cracked all over
my car had 13,500 miles on it...I took it in for its 4 year/30k mile maintenance and they went over the whole car, all they recommended was a brake fluid flush and said my rotors/pads were all fine..
car had to have been tracked, but I would do what the other guys said and have it seen at a reputable Porsche dealer, the PCCB rotors have a different appearance as if they are cracked all over