When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Yes, what others have said, the stick on metal piece needs to be on the outside of your case. This mount is perfect for me, phone has never once fallen off.
Sorry for the thread hijack, but I am trying to figure out what mount this is and what I need to get the actual phone mount to screw in. This was in my car from the previous owner. Is this an older Rennline mount? Will the current magnetic mount screw in? Thanks
Sorry for the thread hijack, but I am trying to figure out what mount this is and what I need to get the actual phone mount to screw in. This was in my car from the previous owner. Is this an older Rennline mount? Will the current magnetic mount screw in? Thanks
I don't think it will work the way you want it to, the Rennline mount uses a RAM attachment mount, very common usage. I would just order a new one from Rennline since they are 15% off at the moment, unless the sale is over with.
@6sigma That is a ProClip mount. It is a vehicle specific base and a swivel mount (which you are missing half of). Good products - I have them in other cars.
Last edited by ChristopherJ; 09-07-2022 at 10:37 AM.
Reason: Forgot to tag
Sorry for the thread hijack, but I am trying to figure out what mount this is and what I need to get the actual phone mount to screw in. This was in my car from the previous owner. Is this an older Rennline mount? Will the current magnetic mount screw in? Thanks
If you have an iPhone I would just unscrew the top part leaving the bare mount. Then buy a strong adhesive magnetic pad. Put that on the mount. Then use an mag safe wireless charger. Keeps my phone charged and no problems sticking to it.
I have a case on my iPhone 13 Pro made by Mous. Says it’s MagSafe compatible but that Rennline magnet is weaker than a mouse fart sending my phone into the abyss if I take a corner faster than 5 mph.
I liked the look of the Walnut case, and really don’t want to stick an adhesive metal plate to backside. I tried putting the metal plate on inside of case, but that in turn screwed up my charging capabilities.
Is there also a permanent mount, like the Rennline one, that sits higher (vents area?). I got an ESR Magsafe charger that's currently connected to the vents, but don't want to be stressing the vents long term.
I have the same scenario and question. The Rennline mount sits too low. Vent solution is not a good long term solution.
It would be nice if there were a lockable arm with a MagSafe pad that extended up to the right of the vents from where the Rennline piece mounts to the console. Looking down to see maps or select tunes is a risk I dont like to take especially where I live and drive.
@6sigma That is a ProClip mount. It is a vehicle specific base and a swivel mount (which you are missing half of). Good products - I have them in other cars.
Thanks! I just ordered the phone holder that will connect to the mount here. Appreciate the ID of the mount as I couldn't figure out what it was!
So before I spend another $60 on this Spiegel Magnetic Charger Mount, I’d like to hear from those that purchased it.
On a scale of 👍🏻 To 👍🏻👍🏻👍🏻👍🏻👍🏻 What’s your overall rating of the ability to securely hold your iPhone 13?
I have the Spiegel on a Rennline mount and it holds my phones securely. However, I have a metal ring affixed to the back of my Pixel 5 and Pixel 6 with no case on either phone.
The one I bought was compatible with the ball already on my Rennline mount. A licensed MagSafe holder and a licensed MagSafe case will hold it perfectly well. Just got to get it on the Rennline mount brack somehow.
The one I bought was compatible with the ball already on my Rennline mount. A licensed MagSafe holder and a licensed MagSafe case will hold it perfectly well. Just got to get it on the Rennline mount brack somehow.
09-06-2022, 10:14 AM
