911obsession Build Thread | Platinum Silver | 997.2 Carrera | Quality Photos
#136
Racer
Thread Starter
Mine is pretty low and NB as well. The rear camber is just about maxed out and front is over 2 degrees on rennline mounts. I have yet to align it so don't know the exact specs. 305/30/19 Michelin PSS looks fairly stretched and the edge sticks out another 4-5mm past the rim edge. Tough to get a good photo in the garage since it's middle of winter here but hope these help. That red C2 is running very aggressive camber, probably more then most would along with a very low suspension. I literally did 2 weeks of research before settling on those figures myself.
Last edited by preelude; 02-11-2019 at 06:43 PM.
#137
Yes, you are correct. I am also lowered and that is what I am basing my measurements on. If your comfortable with running big neg camber then you will be fine. Is BC guaranteeing fitment?
#138
Banned
You car looks great! I think mine will be lower and that is what will make all the difference, the red one I posted seems much lower than yours, I wouldn't consider that aggressive camber either. Here is a photo of Duwerke's old 911 with same specs except 20" (20x9.0 et43 and 20x12.0 et53):
You'll love the wheels. I've had two sets and can't say enough about the quality you get for the money.
#139
Racer
Thread Starter
#140
Racer
Thread Starter
I suppose you can make room if you're willing to go as low as the above car. My photos are a little deceiving due to the angle but I'm pretty sure the top of the tire is tucked both front and rear.
You'll love the wheels. I've had two sets and can't say enough about the quality you get for the money.
You'll love the wheels. I've had two sets and can't say enough about the quality you get for the money.
Last edited by preelude; 02-15-2019 at 11:01 PM.
#141
Racer
Thread Starter
BC Forged KL12 | Brushed Clear | F:19x9 R:19x12
My wheels are ready and getting shipped later today or tomorrow! BC Forged sent me a photo of the finished product, can't wait to see them in person!
The following users liked this post:
Tonggi (12-07-2021)
#142
Rennlist Member
Thats quick for custom built wheels! Cant wait to see them on, will look amazing.
#143
Racer
Thread Starter
#144
Hey Peter! To clear things up for the rest of you, I was only running -1.5 degrees of rear camber and -2 up front. Rear fenders were slightly rolled (as they dont roll very much) and it never rubbed.
#145
Racer
Thread Starter
BC Forged KL12 | Brushed Clear | F:19x9 R:19x12
The wheels have arrived, and I think I am in love! 😍
The following users liked this post:
oalvarez (06-11-2023)
#147
Are the rear wheels more concave than the front? I love the brush metal finish.
#148
Rennlist Member
super happy for you, these look amazing and took no time to get there! did you have a chance to test fit them yet?
#149
Racer
Thread Starter
Thank you
Yes the rears are more concave. Thanks, I love the finish as well
Thank you, I am super happy with them! I will weigh them and try to test fit this afternoon.
#150
Racer
Thread Starter
MRG Titanium Lug Bolts
Perfect timing! My MRG Titanium Lug Bolts arrived today. Just a tad cleaner and lighter than OEM lol.
OEM Lug Bolt Weight: 94g
MRG Titanium Weight: 67g
That is a total of 540g (1lb 3oz) in unsprung weight savings, 135g (4.76oz) per corner. I am happy with that and the rust free future
OEM Lug Bolt Weight: 94g
MRG Titanium Weight: 67g
That is a total of 540g (1lb 3oz) in unsprung weight savings, 135g (4.76oz) per corner. I am happy with that and the rust free future