CEL - Code P2098
#1
CEL - Code P2098
Hi there - 2002 C2, 66,000 miles on chassis, 8,000 miles on factory reman'd engine. Got a CEL the other day, UPS guy finally showed up with my new code reader today. Code shows a P2098. After researching here and Renntech and Google etc. looks like it is most likely the/an O2 sensor.
Does the majority concur/have experience? I realize it could possibly be something else, but I figure if the vast majority of you all point to one thing, then I will take a chance on that assuming it's not too pricey/difficult.
Does the majority concur/have experience? I realize it could possibly be something else, but I figure if the vast majority of you all point to one thing, then I will take a chance on that assuming it's not too pricey/difficult.
#6
I finally caught on to when the error would appear -- after about 30 miles of driving -- and had the code reader already hooked up. I'd sneak a peak at the sensor readings at a stop light and I then saw the drop in voltage, the flattening of the high voltage reading and other changes and once or twice I was observing this on the code reader when the CEL came on.
I was satisfied then and changed not only the sensor the error code pointed to but its matching sensor on the other side.
Trending Topics
#11
Well, just this evening the code came back again. Same code, just driving normally, car in warmup phase. It's been 1 year, 8 months and about 9000 miles since the last occurrence. I did just change the oil a few days ago. I reset the code again and we'll see if it comes back...
The bummer is I'm taking it on a trip to Indiana about a week from now. So about 2600 miles round trip, it'll be annoying if it comes on during the trip...If it comes on again before I leave I suppose I will try to figure out which of the four 02 sensors it is. I do not want to get stranded en route...
Edited: I just found this: http://www.underhoodservice.com/tech...096-p2098-set/
It was published after my first occurrence of this issue. Interesting.
The bummer is I'm taking it on a trip to Indiana about a week from now. So about 2600 miles round trip, it'll be annoying if it comes on during the trip...If it comes on again before I leave I suppose I will try to figure out which of the four 02 sensors it is. I do not want to get stranded en route...
Edited: I just found this: http://www.underhoodservice.com/tech...096-p2098-set/
It was published after my first occurrence of this issue. Interesting.
#12
Well, just this evening the code came back again. Same code, just driving normally, car in warmup phase. It's been 1 year, 8 months and about 9000 miles since the last occurrence. I did just change the oil a few days ago. I reset the code again and we'll see if it comes back...
The bummer is I'm taking it on a trip to Indiana about a week from now. So about 2600 miles round trip, it'll be annoying if it comes on during the trip...If it comes on again before I leave I suppose I will try to figure out which of the four 02 sensors it is. I do not want to get stranded en route...
Edited: I just found this: http://www.underhoodservice.com/tech...096-p2098-set/
It was published after my first occurrence of this issue. Interesting.
The bummer is I'm taking it on a trip to Indiana about a week from now. So about 2600 miles round trip, it'll be annoying if it comes on during the trip...If it comes on again before I leave I suppose I will try to figure out which of the four 02 sensors it is. I do not want to get stranded en route...
Edited: I just found this: http://www.underhoodservice.com/tech...096-p2098-set/
It was published after my first occurrence of this issue. Interesting.
So if the TSB applies to your VIN, maybe a dealer visit is needed for reprogramming opf the DME. If not, just replace your bank2 precat O2 sensor (according to the Bentley repair manual info re P2098)
#13
#14
The article in the link has a critical error. The original TSB (available from Renntech) says "In vehicles produced before the date of introduction stated below, the Check Engine warning light may be activated by an error in the diagnosis software of the DME control module. ", which makes a lot more sense.
So if the TSB applies to your VIN, maybe a dealer visit is needed for reprogramming opf the DME. If not, just replace your bank2 precat O2 sensor (according to the Bentley repair manual info re P2098)
So if the TSB applies to your VIN, maybe a dealer visit is needed for reprogramming opf the DME. If not, just replace your bank2 precat O2 sensor (according to the Bentley repair manual info re P2098)
http://workshop-manuals.com/porsche/...096/p2098_set/
As far as I can tell it would apply to any '02. Thanks for letting me know WHICH of the O2 sensors would be the one in question if reprogramming he DME did not work. Now I wonder what that costs and somehow can still find it within myself to be surprised that any manufacturer would let the customer be charged for reprogramming of something that should have been right from the get-go no matter how old the car is. It's not like software degrades over time or miles or be affected by how the car was treated or where it was serviced...
#15
I've asked Loren and John over Renntech. Watch out for the final verdict on which O2 sensor P2098 refers to
http://www.renntech.org/forums/topic...s/#entry259389
http://www.renntech.org/forums/topic...s/#entry259389