993 Front Windshield Replacement Cost
#31
Drifting
Too many Hauryble stories about these guys! Euroglass did my 911SC front and rear glass following a restorative repaint. Everything was done to perfection with these guys!
#32
Well, I've had a bit of an ordeal this past week having the original windshield replaced on my 993. After getting several quotes, took it last week to a reputable local shop which was recommended by a friend who had his '97 993 Turbo's windscreen replaced there a few weeks earlier. They had a Pilkington windscreen in stock, which was listed as an "OE" replacement. Cost was $840 installed, including tax... not bad compared to what the local Porsche dealer and several other glass shops quoted, which were all over $1K.
They completed the job with no apparent issues, and I was happy to finally have a new windshield. Well, as I was driving home from the shop, happy to be looking through perfectly clear, pit free new glass, I noticed the black urethane sealant had squeezed up over the inner rubber seal all across the lower edge, right in front of the leading edge of the upper dash. Sloppy install job... not good!
Called the shop the next day, and they said they "stand behind their work", and that they'd either clean it up or replace the new windshield with another new windshield free of charge. They asked me if I could bring it out for them to look at, so I did the next day and they determined that they could not clean up the excess sealant, and would need to replace the new windshield with another new one.
Sooo.... took it back yesterday....they'd ordered another new windscreen -- Sigla this time. The installer who did the job the first time (and who the shop manager said was the guy they use for "high end" car glass installations) said the Pilkington didn't fit as well as he'd like... he said it was slightly "raised" in the lower middle of the glass such that it didn't lay flat against the frame/gasket.
Anyway, they're supposed to install the new replacement of the new replacement today.... we'll see how it turns out this time. With luck this one will turn out fine and only cost me a little extra time and aggravation in dealing with a botched windshield install job.
They completed the job with no apparent issues, and I was happy to finally have a new windshield. Well, as I was driving home from the shop, happy to be looking through perfectly clear, pit free new glass, I noticed the black urethane sealant had squeezed up over the inner rubber seal all across the lower edge, right in front of the leading edge of the upper dash. Sloppy install job... not good!
Called the shop the next day, and they said they "stand behind their work", and that they'd either clean it up or replace the new windshield with another new windshield free of charge. They asked me if I could bring it out for them to look at, so I did the next day and they determined that they could not clean up the excess sealant, and would need to replace the new windshield with another new one.
Sooo.... took it back yesterday....they'd ordered another new windscreen -- Sigla this time. The installer who did the job the first time (and who the shop manager said was the guy they use for "high end" car glass installations) said the Pilkington didn't fit as well as he'd like... he said it was slightly "raised" in the lower middle of the glass such that it didn't lay flat against the frame/gasket.
Anyway, they're supposed to install the new replacement of the new replacement today.... we'll see how it turns out this time. With luck this one will turn out fine and only cost me a little extra time and aggravation in dealing with a botched windshield install job.
#33
Rennlist Member
Join Date: Oct 2010
Location: Naphill
Posts: 985
Likes: 0
Received 0 Likes
on
0 Posts
1. You need the right height/thickness on the bead of urethane so it bonds to the back of the glass so you don't get overspill on the inside trim but you want it just right or to much or to little you end up with the famous 993 squeak or a leak if it's to thin
2. With 993's it all about the way you apply the urethane you want the bead of urethane to touch the inner part of the back of the screen where the raised part on the back edge is & not touch the hard plastic outer trim on the screen were the outer trim clips into so all the glue is uniform and touching the inner raised part of the new screen.
3. When you install the screen you need to make sure it sits central in the hole and the hard plastic outer trim on glass is not touching the apiture of the frame so not to squeak/leak.
4. If you use a new outer trim the glass tends to be more " springy" in the hole so I tend to use a strap to help it stay put while the screen sets.
5. When I do 993 screens I ask if the customer wants me to fill the gap between the glass & apiture as Porsche tell you but that's a like a "what oil do I use in my 993"
I've been doing this since 88 & remember when the **** ups started back then when the 993 came out and there still going on....but sounds like you guys in the states have found the good guys in some states
There not a hard job to do but fairly time consuming when you have to treat the rust if any & you just need have I bit of experience to get the nack of getting it spot on
Hope this helps...fuch
2. With 993's it all about the way you apply the urethane you want the bead of urethane to touch the inner part of the back of the screen where the raised part on the back edge is & not touch the hard plastic outer trim on the screen were the outer trim clips into so all the glue is uniform and touching the inner raised part of the new screen.
3. When you install the screen you need to make sure it sits central in the hole and the hard plastic outer trim on glass is not touching the apiture of the frame so not to squeak/leak.
4. If you use a new outer trim the glass tends to be more " springy" in the hole so I tend to use a strap to help it stay put while the screen sets.
5. When I do 993 screens I ask if the customer wants me to fill the gap between the glass & apiture as Porsche tell you but that's a like a "what oil do I use in my 993"
I've been doing this since 88 & remember when the **** ups started back then when the 993 came out and there still going on....but sounds like you guys in the states have found the good guys in some states
There not a hard job to do but fairly time consuming when you have to treat the rust if any & you just need have I bit of experience to get the nack of getting it spot on
Hope this helps...fuch
#34
Thanks for the tutorial Fuch... replacing these windshield properly sounds like you really have to know what you're doing. Beyond the scope of most local glass shops, unfortunately. Too bad you're across the pond and not around here to do the job properly!
On the rust... yes, there was some surface rust on both lower corners -- they showed it to me when the windscreen was out -- but fortunately no rust through. They sanded it off and applied some etching primer over the area. Since I don't drive it in the wet or wash it very often (I use Griot's waterless carwash or Speedshine to clean the car, as it never gets really dirty) hopefully this will take care of it.
On the rust... yes, there was some surface rust on both lower corners -- they showed it to me when the windscreen was out -- but fortunately no rust through. They sanded it off and applied some etching primer over the area. Since I don't drive it in the wet or wash it very often (I use Griot's waterless carwash or Speedshine to clean the car, as it never gets really dirty) hopefully this will take care of it.
#35
Rennlist Member
Join Date: Oct 2010
Location: Naphill
Posts: 985
Likes: 0
Received 0 Likes
on
0 Posts
Im over in boston over xmas this year so i will bring my tools!!...
If you look at this pic i have you can see im using my finger as a guide to keep the glue in the right place as i gun it round so its uniform and not to far out or to far in so no overspill on the inside
Bit of rust before!!
After a bit of tlc...
Getting there....
Afrer....
This car was a rs track rat so had no inner trim but the pics give you a idea....
If you look at this pic i have you can see im using my finger as a guide to keep the glue in the right place as i gun it round so its uniform and not to far out or to far in so no overspill on the inside
Bit of rust before!!
After a bit of tlc...
Getting there....
Afrer....
This car was a rs track rat so had no inner trim but the pics give you a idea....
Last edited by fuch; 06-17-2012 at 05:13 PM.
#36
Figured I'd throw this out there for the record, I got the car back last Thursday and it looks great. No gaps in the trim, no leaks, and nearly no creaks. We basically concluded that the body shop pulled the tape off the car before the urethane cured and pretty likely the door was slammed shut with the windows/sunroof closed. Two thumbs up to Mark and the guys at Service Auto Glass for making this right!
#37
Instead of starting another thread, I'll add here and hope I don't get in trouble.
I just got a new windshield at Safelite. 2.5 hours to replace the original glass and put a new OEM Pilkington one in. No corrosion of any type, "virginous" the tech described it as... $1200... insurance covered it...
I just got a new windshield at Safelite. 2.5 hours to replace the original glass and put a new OEM Pilkington one in. No corrosion of any type, "virginous" the tech described it as... $1200... insurance covered it...
#38
I would recommend Safelite Auto Glass in Pasadena, 626-792-0618 ask for Ken ( mgr )
They did mind last year and very happy with their price and knowledge with the installation.
______________
'97 Blk/Blk C2S
They did mind last year and very happy with their price and knowledge with the installation.
______________
'97 Blk/Blk C2S
#41
#42
Rennlist Member
1. You need the right height/thickness on the bead of urethane so it bonds to the back of the glass so you don't get overspill on the inside trim but you want it just right or to much or to little you end up with the famous 993 squeak or a leak if it's to thin
2. With 993's it all about the way you apply the urethane you want the bead of urethane to touch the inner part of the back of the screen where the raised part on the back edge is & not touch the hard plastic outer trim on the screen were the outer trim clips into so all the glue is uniform and touching the inner raised part of the new screen.
3. When you install the screen you need to make sure it sits central in the hole and the hard plastic outer trim on glass is not touching the apiture of the frame so not to squeak/leak.
4. If you use a new outer trim the glass tends to be more " springy" in the hole so I tend to use a strap to help it stay put while the screen sets.
5. When I do 993 screens I ask if the customer wants me to fill the gap between the glass & apiture as Porsche tell you but that's a like a "what oil do I use in my 993"
I've been doing this since 88 & remember when the **** ups started back then when the 993 came out and there still going on....but sounds like you guys in the states have found the good guys in some states
There not a hard job to do but fairly time consuming when you have to treat the rust if any & you just need have I bit of experience to get the nack of getting it spot on
Hope this helps...fuch
2. With 993's it all about the way you apply the urethane you want the bead of urethane to touch the inner part of the back of the screen where the raised part on the back edge is & not touch the hard plastic outer trim on the screen were the outer trim clips into so all the glue is uniform and touching the inner raised part of the new screen.
3. When you install the screen you need to make sure it sits central in the hole and the hard plastic outer trim on glass is not touching the apiture of the frame so not to squeak/leak.
4. If you use a new outer trim the glass tends to be more " springy" in the hole so I tend to use a strap to help it stay put while the screen sets.
5. When I do 993 screens I ask if the customer wants me to fill the gap between the glass & apiture as Porsche tell you but that's a like a "what oil do I use in my 993"
I've been doing this since 88 & remember when the **** ups started back then when the 993 came out and there still going on....but sounds like you guys in the states have found the good guys in some states
There not a hard job to do but fairly time consuming when you have to treat the rust if any & you just need have I bit of experience to get the nack of getting it spot on
Hope this helps...fuch
#43
some insurances have a $100 deductible on windshield replacement....even if the rest of your deductible is higher.
had $1K deductible and after simply buying new windshields over the years when needed and paying for them...'found' that out when wife's suv needed one...ouch.
check w insurance agent.
otherwise...quad is right...$800-1000 for glass...another $100 or so for seals and install $1-200.
you want someone who had done a lot...otherwise...higher chance of squeak and/or leak
had $1K deductible and after simply buying new windshields over the years when needed and paying for them...'found' that out when wife's suv needed one...ouch.
check w insurance agent.
otherwise...quad is right...$800-1000 for glass...another $100 or so for seals and install $1-200.
you want someone who had done a lot...otherwise...higher chance of squeak and/or leak
#45
Rennlist Member
Recommendations in NYC area?
A 5 inch crack opened up over the weekend.
A 5 inch crack opened up over the weekend.