Recap of the SAI circuit
#256
Added: added coreseller and boostid to 2nd round list, changed Tom97C4S's order to 2 + enclosures
This list for the first round of boards is now closed. I've started a Waiting/Back-up list below for those that missed this first run.
Quick reminders:
1) unless otherwise noted, it's assumed you are asking for an assembled unit.
2) enclosures are optional - feel free to update/ Post a reply/ PM and I'll update the list if you are looking for an enclosure.
Payment Info posted by Lewis (from post #147):
Once assembled, I will start sending PM's so folks can provide me their shipping addresses. Inside the package will be the unit, a hardcopy of the schematic, a hardcopy of the PCB layout and a return address envelope. When you get the unit and everything is OK, just use the envelope to send payment. I am a trusting person when it comes to RL members, so I have no problem sending out the units prior to receiving payment.
Backup/Waiting/2nd Round List
This list for the first round of boards is now closed. I've started a Waiting/Back-up list below for those that missed this first run.
Quick reminders:
1) unless otherwise noted, it's assumed you are asking for an assembled unit.
2) enclosures are optional - feel free to update/ Post a reply/ PM and I'll update the list if you are looking for an enclosure.
Payment Info posted by Lewis (from post #147):
Once assembled, I will start sending PM's so folks can provide me their shipping addresses. Inside the package will be the unit, a hardcopy of the schematic, a hardcopy of the PCB layout and a return address envelope. When you get the unit and everything is OK, just use the envelope to send payment. I am a trusting person when it comes to RL members, so I have no problem sending out the units prior to receiving payment.
- vincer77 - 1
- Rick Lee - 1
- Aircooled Dave - 1
- michaelh993 - 2
- tonypai - 1 + enclosure
- fullbooker - 1 + enclosure
- NP993 - 1 + enclosure
- flying low - 4
- ilko - 1 + enclosure
- 600RR - 2 + 1 enclosure only
- Shahrams - 2 + enclosures
- bw993 - 1
- tbil - 1 + enclosure
- Teddy2 - 1 + enclosure
- Ash - 1 + enclosure
- 993BillW - 1 + enclosure
- Dan V - 1 kit
- efong - 1 + enclosure
- AW21 - 2 + enclosures
- NC TRACKRAT - 1 assembled + 1 kit + 2 enclosures
- cabrio993 - 1
- Paul M - 1 + enclosure
- tropheus - 2 + enclosures
- C4SJOHN - 2 + enclosures
- MDamen - 1
- TheBen - 1
- JPS - 1
- air993 - 1 + enclosure
- alpinadvl - 1 + enclosure
- rsa964 - 1
- cdmdriver - 1
- Jeff96-993 - 1 + enclosure
- Kaefer - 2 + enclosures
- SimonM_98 - 1
- CarreraX - 2 + enclosures
- skypig - 1 + enclosure
- Don't lift - 1 + enclosure
- 2ndof2 - 1
- Richard W - 1 assembled + 1 kit + 1 enclosure
- Amfab - 1 + enclosure
- M Fig - 2
- e3photo - 1
- 911Dave - 1
- kraftsman - 1 + enclosure
- PNogC2S - 1
- CAHRERA - 1
- slapshot - 1 + enclosure
- bpras@msn.com - 2
- Blue TTop - 2 + enclosures
- rdevany - 1 kit + 1 enclosure
- earossi - 1 + enclosure
- sdrake - 1
- cmat - 1 kit + enclosure
- Teddy2 - 1 + enclosure
- jaguarandi - 1 + enclosure
- Biggdawg - 2 + enclosures
- mike cap - 1 + enclosure
- deekay911 - 1 + enclosure
- helmet993 - 1 + enclosure
- ppressle - 1 kit
- southsong - 1 + enclosure
- V33 - 2 + enclosures
- nels415 - 1 + enclosure
- vr416v - 1 + enclosure
- Don Plumley - 1
- Matt Lane -1 + enclosure
- Jim W - 1 + enclosure
- TxnBluDvl - 2 + enclosures
- mpgandco - 2 + enclosures
- GRINBOB - 1 kit + 1 enclosure
- beagling - 1 + enclosure
- Jscanavan - 2 kits + 2 enclosures
- Richard Lee - 1 + enclosure
- dbog - 1 + enclosure
- bootman30 - 1
- 77'3.6vram - 3 + enclosures
Backup/Waiting/2nd Round List
- DryFly - 1 + enclosure
- ESL - 1 + enclosure
- timothymoffat - 2 + enclosures
- suffi - 1 kit
- tom97c4s - 2 + enclosures
- lizSter - 1 + enclosure
- SCMomentum - 2 + enclosures
- elfefan - 1 + enclosure
- deadeye - 2 + enclosures
- FisterD - 4 + enclosures
- rc16 - 2 + enclosures
- tbrom - 1 + enclosure - Please Confirm
- jimbo3 - 2 + enclosures
- skl2 - 2 + enclosures
- mikej - 2 + enclosures
- GC96 - 1 + enclosure
- Cincy_Ron - 1 kit + enclosure
- coreseller - 1 + enclosure
- boostid - 1 + enclosure
Last edited by Ash; 11-15-2011 at 11:56 AM.
#259
I know I am late geting to this thread but I would surely like to be on the second list for the part and enclosures, etc. I had a 993 previously and am currently looking to purchase another if I can find a 98 993 Targa. I had one that had the dreaded CEL issue due to the SAI - it was fixed under warranty by the PO that I purchased from. It had the valve guides replaced as well - shouldn't have sold that car but that's another story. I am getting in late - what is the process - do you mail them individually or no? Sorry for asking and this is just an unreal thing that you are doing Lewis. I am amazed at this effort for such a problem on the 993.
#260
Midweek update ....
Minor issue with the electrolytic capacitor hitting the cover of the enclosure....my bad, it is about 1-2 mm too tall using the standard 11mm height cap I chose.
Minor issue with one of the PCB mounting holes not quite lining up with one if the 2 mounting bosses in the enclosure. Won't be an issue.
The enclosures look very nice and are small which should allow for easy mounting.
New (shorter) cap has already been ordered/shipped and as soon as they arrive I will swap them out and finish electrical test.
I will drill out one of the 2 mounting holes to line up, even though one mounting screw is sufficient to mount the PCB to the enclosure bottom.
Sorry for the short delay...I need to work on my metric addition and mechanical skills
Minor issue with the electrolytic capacitor hitting the cover of the enclosure....my bad, it is about 1-2 mm too tall using the standard 11mm height cap I chose.
Minor issue with one of the PCB mounting holes not quite lining up with one if the 2 mounting bosses in the enclosure. Won't be an issue.
The enclosures look very nice and are small which should allow for easy mounting.
New (shorter) cap has already been ordered/shipped and as soon as they arrive I will swap them out and finish electrical test.
I will drill out one of the 2 mounting holes to line up, even though one mounting screw is sufficient to mount the PCB to the enclosure bottom.
Sorry for the short delay...I need to work on my metric addition and mechanical skills
#261
If/when there is a second run, please put me down for two complete units with enclosures. No particular rush.
Can't say "thanks" enough to Flying_Low and Lewis for design and production as well as the others who offered their knowledge and expertise.
Can't say "thanks" enough to Flying_Low and Lewis for design and production as well as the others who offered their knowledge and expertise.
#262
This is what happens when you don't pay attention to stickies!!!
Lewis...I am in no rush...but if there is another run I will take two assembled units with enclosures.
Thanks for doing this!!! I just did the port flush and it was the least fun job I have ever done!!
Lewis...I am in no rush...but if there is another run I will take two assembled units with enclosures.
Thanks for doing this!!! I just did the port flush and it was the least fun job I have ever done!!
#263
Of course I'm late! Damn. If there is another run of these, I'd sure like to get in on this.
So please put me down on the waiting list for 2 units, fully assembled with enclosures.
I'm in complete agreement with other posters; Lewis should be recommended for sainthood. And thank you! Ash for keeping the List.
Mike
'96 993c2
So please put me down on the waiting list for 2 units, fully assembled with enclosures.
I'm in complete agreement with other posters; Lewis should be recommended for sainthood. And thank you! Ash for keeping the List.
Mike
'96 993c2
#266
Update,
UPS did not deliver the new (shorter) caps in time for this weekend
Now scheduled for delivery end of business day on Monday.
Once I have them, I will install and test the boards.
Sorry for the delay...
UPS did not deliver the new (shorter) caps in time for this weekend
Now scheduled for delivery end of business day on Monday.
Once I have them, I will install and test the boards.
Sorry for the delay...
#267
Update for those on the waiting list/2nd round.
Per the PCB pricing (bare board) in post 107 of this thread...
$11.94 each for 25 pcs
$6.50 each for 50 pcs
$3.78 each for 100 pcs
We are at 25 people. I don't know if we will get to 100, so the 2nd round cost might be higher than the first.
I will leave it up to the members to decide when to place the 2nd order and if that price is acceptable.
Again, i am charging cost for the materials and shipping, nothing more.
Per the PCB pricing (bare board) in post 107 of this thread...
$11.94 each for 25 pcs
$6.50 each for 50 pcs
$3.78 each for 100 pcs
We are at 25 people. I don't know if we will get to 100, so the 2nd round cost might be higher than the first.
I will leave it up to the members to decide when to place the 2nd order and if that price is acceptable.
Again, i am charging cost for the materials and shipping, nothing more.
#268
Lewis, speaking for me, I'm not in a hurry so I can wait for 50 or 100. Others may have a CEL currently and need them ASAP. Perhaps someone from the 1st order could help out such a fellow renlister in need. I think over time another 100 will be wanted as more of us READ THE STICKY!!!!! From my perspective you could easily charge $50.00 and no one would complain.
Last edited by Deadeye; 11-12-2011 at 05:24 PM. Reason: sp
#269
Lewis and Ash, thank you for the work. Been a Porsche owner for many years, a 993 owner for a few weeks now. Please ad me to your list for an assembled unit with enclosure for your next batch........Mark.
Last edited by coreseller; 11-14-2011 at 11:09 PM.
#270
Much thanks and appreciation to Lewis and Ash.
Please include me on the second list for an assembled unit with enclosure.
Are the instructions clear enough for an idiot to install this?
Thanks again
Please include me on the second list for an assembled unit with enclosure.
Are the instructions clear enough for an idiot to install this?
Thanks again