When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
I purchased the new soul cats from John and combine with akropovic exhaust. I remember a post from @bigswole I think where he said cold start was 12/10. It is quite loud and glorious. No CEL and ~150 miles last night after install.
Install was 3/10 and took about 4 hours going nice and slow. Hardest part as @4rings has said is the V clamp on stock cats. Trick is WD-40 night before and a 10” vice clamp on the flat rectangular tip of the bolt. Once you drop the cats a smidge open end 22mm wrench in O2 sensor and you are golden.
Of course I had to try without removing the bumper cover even though I was told it wasn’t possible. Shocker it is not. 🤷🏻♂️
Battery operated ratchet makes things go faster. Etorx is the “fanciest” tool you need other than standard torx and hex bits.
I removed the wheels as that’s easy enough but you could probably do it without. Three screws under with wheel well cover. I did have separate magnetic pans for each major section just to keep things easy.
Valve controller transfers over easy. Just get the spring right and the butterfly’s should be open. Confirm by looking at your current PSE.
other than that no surprises. I’m terrible at documenting pictures but here are a few and a short cold start video.
Is the video there and I'm missing it, or are you only teasing us? I'm on the hunt for a new exhaust set up; watched more videos than I care to count, but always come back to the Arka. Can't wait to hear her.
Is the video there and I'm missing it, or are you only teasing us? I'm on the hunt for a new exhaust set up; watched more videos than I care to count, but always come back to the Arka. Can't wait to hear her.
Ah sorry video was too big. Had to get to my laptop. Cold Start
Thanks for the write up. Getting a not found error for the link. Question: the fabspeed video and another (can't remember which) shows install of the akropovic and cats being installed with the bumper in place. What changed? Also, where are you located? 😁 PS. Way to utilize the wall rack!
If you are doing the tips bumper cover has to come off. Cats are easy and don’t require that. Once you fix the v clamps they are way easy. I don’t know about the other persons install but I could not pivot out the PSE without the valve controllers hitting. I thought I’d done it before on the soul valved exhaust but maybe I did not. The Akra could easily go in by its self with no tips I suppose if you had a standard exhaust?
Now I see why you asked about the butterfly valves, DIY @ home, nice!
Glad to see everything worked out smoothly and everything flows together nicely.
Thanks again for the purchase!
-Josh
**For anyone interested we have the 992 Soul cats in stock and Akrapovic slip on systems**
__________________ Your #1 Dealer for Aftermarket Performance Products
BC Forged / Soul Performance / Akrapovic / Bilstein / HRE / AL13 / CSF + more Orange County, CA Email: info@merakiautoworks.com Text/Call: 213 394 2886 Website:www.MerakiAutoworks.com
Last edited by Meraki Autoworks; 02-26-2023 at 02:45 PM.
I purchased the new soul cats from John and combine with akropovic exhaust. I remember a post from @bigswole I think where he said cold start was 12/10. It is quite loud and glorious. No CEL and ~150 miles last night after install.
Install was 3/10 and took about 4 hours going nice and slow. Hardest part as @4rings has said is the V clamp on stock cats. Trick is WD-40 night before and a 10” vice clamp on the flat rectangular tip of the bolt. Once you drop the cats a smidge open end 22mm wrench in O2 sensor and you are golden.
Of course I had to try without removing the bumper cover even though I was told it wasn’t possible. Shocker it is not. 🤷🏻♂️
Battery operated ratchet makes things go faster. Etorx is the “fanciest” tool you need other than standard torx and hex bits.
I removed the wheels as that’s easy enough but you could probably do it without. Three screws under with wheel well cover. I did have separate magnetic pans for each major section just to keep things easy.
Valve controller transfers over easy. Just get the spring right and the butterfly’s should be open. Confirm by looking at your current PSE.
other than that no surprises. I’m terrible at documenting pictures but here are a few and a short cold start video.
DAVE DAVE DAVE… car looks great. But man I gota bust your chops on the garage…. Spend less time at the stars games and more time organizing that garage buddy!