991.2 GT3 Dundon Power package Test
#1
8th Gear
Thread Starter
991.2 GT3 Dundon Power package Test
Hello everyone! Please pardon any mistakes, as this is the first time I have published on Renlist. I recently did the full power package from Dundon on my 991.2 GT3 and figured the data would be of interest to everyone.
Products- Dundon catted Street headers, 93mm Throttle body, Plenum IMPORTANT NOTE: I am running factory center muffler, so i am loosing a little power over the Dundon Loud center.
Install- Was smooth, it does require some patience to ensure the plenum does not have any leaks. I would highly recommend using someone who has experience with Porsche vs a general speed shop.
Initial reaction: I felt that the car needed to learn a little bit. Once it did WOW was it a different animal. It really changed the tone of the car, and you can certainly feel the difference at the top of the rev range. Obviously a butt dyno doesn't do anyone good so i wanted to get some real data. We had a PCA club weekend right after install and i was with 3 friends 2 of which had bone stock GT3's so it was a great comparison on track. I also did some pre and post runs with a draggy and i wanted to share that data in the event it helps someone.
Stock GT3 60-130 runs PDK
1200Ft of elevation
65 degree ambient temps
Valid slope per Draggy
Dundon Package GT3 60-130 PDK
1200ft of elevation
67 ambient tempature
SAME ROAD as previous pulls done 2 days prior
Valid slope per Draggy
Now onto lap times. Again , i didn't think i was going to notice anything so my expectations were pretty low. I know there is a lot of variables with this data but i found it interesting.
Brained International Raceway Long course
VMax on the long straight with my friends stock GT3 166mph
Vmax on the long straight with my dundon GT3 171mph
Same driver, Similar fuel loads. The data above was best case, however i will say the dundon car could consistently get 2 MPH over the stock car.
Lap times (i know hard to do apples to apples) But we tried!
1:45.88 stock GT3
1:44.53 Modified GT3
With this, we really looked at the Apex Pro data and overlaid the data to see if we were picking up MPH in corner exit/in. It was harder to tell but the Dundon car was always slightly ahead with the same driver and as close to the same fuel levels as possible. Laps were done back to back.
Over all, i would strongly recommend the power package. I was goinig to do just the headers at first, but im glad that i did the plenum and the new airbox. You can feel the car just breathes better, and i would imagine the thing really comes alive with a tune! The sound you get from the slower moving air inside that plenum is pretty cool. I think its safe to say everyone knows how good the exhaust/headers sound but it was a nice surprise to hear the sound of that airbox/plenum doing its thing!
I dont think anyone else can come close to the real world gains Dundon advertises (and i have tested). I have been impressed with the service and quality most importantly. The guys really know there stuff!
Please reach out if i can help. I have a lot of data i can share. I attempted to upload as much as i could here (NEWB) but happy to email it out to whoever needs it.
Thanks
Dan
997 C2S-Sold
991.1 TurboS- Sold
991.1 GT3- Sold
991.2 GT3
991.2 GT3RS (incoming, and it will 100% have this dundon set up as well)
Dundon installed
Stock
Dundon Installed
Vmax stock
Products- Dundon catted Street headers, 93mm Throttle body, Plenum IMPORTANT NOTE: I am running factory center muffler, so i am loosing a little power over the Dundon Loud center.
Install- Was smooth, it does require some patience to ensure the plenum does not have any leaks. I would highly recommend using someone who has experience with Porsche vs a general speed shop.
Initial reaction: I felt that the car needed to learn a little bit. Once it did WOW was it a different animal. It really changed the tone of the car, and you can certainly feel the difference at the top of the rev range. Obviously a butt dyno doesn't do anyone good so i wanted to get some real data. We had a PCA club weekend right after install and i was with 3 friends 2 of which had bone stock GT3's so it was a great comparison on track. I also did some pre and post runs with a draggy and i wanted to share that data in the event it helps someone.
Stock GT3 60-130 runs PDK
1200Ft of elevation
65 degree ambient temps
Valid slope per Draggy
- 9.23 seconds
- 9.11 seconds
- 9.32 seconds
- 9.03 seconds
Dundon Package GT3 60-130 PDK
1200ft of elevation
67 ambient tempature
SAME ROAD as previous pulls done 2 days prior
Valid slope per Draggy
- 8.70 seconds
- 8.93 seconds
- 8.42 seconds
- 8.49 seconds
Now onto lap times. Again , i didn't think i was going to notice anything so my expectations were pretty low. I know there is a lot of variables with this data but i found it interesting.
Brained International Raceway Long course
VMax on the long straight with my friends stock GT3 166mph
Vmax on the long straight with my dundon GT3 171mph
Same driver, Similar fuel loads. The data above was best case, however i will say the dundon car could consistently get 2 MPH over the stock car.
Lap times (i know hard to do apples to apples) But we tried!
1:45.88 stock GT3
1:44.53 Modified GT3
With this, we really looked at the Apex Pro data and overlaid the data to see if we were picking up MPH in corner exit/in. It was harder to tell but the Dundon car was always slightly ahead with the same driver and as close to the same fuel levels as possible. Laps were done back to back.
Over all, i would strongly recommend the power package. I was goinig to do just the headers at first, but im glad that i did the plenum and the new airbox. You can feel the car just breathes better, and i would imagine the thing really comes alive with a tune! The sound you get from the slower moving air inside that plenum is pretty cool. I think its safe to say everyone knows how good the exhaust/headers sound but it was a nice surprise to hear the sound of that airbox/plenum doing its thing!
I dont think anyone else can come close to the real world gains Dundon advertises (and i have tested). I have been impressed with the service and quality most importantly. The guys really know there stuff!
Please reach out if i can help. I have a lot of data i can share. I attempted to upload as much as i could here (NEWB) but happy to email it out to whoever needs it.
Thanks
Dan
997 C2S-Sold
991.1 TurboS- Sold
991.1 GT3- Sold
991.2 GT3
991.2 GT3RS (incoming, and it will 100% have this dundon set up as well)
Dundon installed
Stock
Dundon Installed
Vmax stock
The following users liked this post:
RockyTopTenn (10-16-2019)
The following users liked this post:
RLX_556 (10-16-2019)
#4
Very cool. Mine is at the shop getting installed this week. Hope to have it back by Friday just in time for hopefully some decent weather this weekend to do some testing.
#5
Basic Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
For the 991.2 GT3 the base package is Street Headers - $7295, 93mm Center Plenum/93mm Throttle Body - $3195, Dual Cone Air filter box - $4795 we discount the package so it comes to: $14,368
Intake air temps are a bit difficult to control on the dyno, so we were looking for ways to show the performance gains in the real world, hence the 60-130, lap times and end of straight MPH improvements.
991.2 GT3 PDK Dundon Power Package
Excited for you!
991.2 GT3 PDK Dundon Power Package
Excited for you!
__________________
Dundon Motorsports
Gig Harbor, WA
253-200-4454
jamie@dundonmotorsports.com
www.dundonmotorsports.com
Facebook.com/dundonmotorsports
Instagram @dundon_motorsports
Dundon Motorsports
Gig Harbor, WA
253-200-4454
jamie@dundonmotorsports.com
www.dundonmotorsports.com
Facebook.com/dundonmotorsports
Instagram @dundon_motorsports
The following users liked this post:
RLX_556 (10-16-2019)
#6
8th Gear
Thread Starter
Hey! I do actually have charts. They were on a mustang dyno, ill see if i can locate it for you. It was real HP though. Intake temps were not apples to apples though.
Trending Topics
#9
Just picked her up. Sound is amazing. So much better than stock. I plan to test with the dragy this weekend.
Also swapped out the gold wheels with some black BBS FI-R’s. Personally, I like the look much better.
Also swapped out the gold wheels with some black BBS FI-R’s. Personally, I like the look much better.
#10
Rennlist Member
Join Date: Feb 2006
Location: Wishing I Was At The Track
Posts: 13,608
Received 1,842 Likes
on
955 Posts
Averaging out these numbers shows a little over 6% faster times w/the package. Once you allow for non-linear change in air resistance as speed increases that's pretty much in line with what Dundon are showing on the dyno in terms of HP gains. Pretty good real-world validation.
Last edited by Nizer; 10-16-2019 at 11:17 PM.
The following 2 users liked this post by Nizer:
Jamie@dundonmotorsports (10-16-2019),
SterlingatBOM (10-18-2019)
#11
Basic Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
I'm talking to our Aero development guys to see if we can get drag numbers and account for the non linearity, and back out the power for 60-130 increases. That math is a little harder than 1/4 mile trap speed...
#12
8th Gear
Thread Starter
Averaging out these numbers shows a little over 6% faster times w/the package. Once you allow for non-linear change in air resistance as speed increases that's pretty much in line with what Dundon are showing on the dyno in terms of HP gains. Pretty good real-world validation.
#13
Addict
Rennlist Member
Rennlist Member
60-130 mph is particularly useful, as many racetracks cover that range from corner exit followed by a moderately lengthy straight
The following users liked this post:
RLX_556 (10-27-2019)
#15
Me too. Gold wheels look okay on some colors of cars, but to my eye, it doesn't look right on a silver car. I had my Aurum Gold Satin magnesium wheels painted to the Platinum Satin color. Looks a lot better against the silver car.