Notices
964 Forum 1989-1994
Sponsored by:
Sponsored by:

How to remove a 964 rear quarter window

Thread Tools
 
Search this Thread
 
Old 10-15-2015 | 07:08 PM
  #16  
dsan's Avatar
dsan
Racer
 
Joined: Oct 2013
Posts: 350
Likes: 45
From: Southern GA
Default

Did everyone use the sealing strap 00004312900 that goes under the black trim when putting the windows back in or is there an alternative? Is that the dum dum or sealant? I'd hate to buy a 10 meter roll just for the meter needed and trash the rest.
Old 10-15-2015 | 07:14 PM
  #17  
John McM's Avatar
John McM
Thread Starter
Rennlist Member
 
Joined: May 2001
Posts: 13,315
Likes: 652
From: Auckland, New Zealand.
Default

Originally Posted by dsan
Did everyone use the sealing strap 00004312900 that goes under the black trim when putting the windows back in or is there an alternative? Is that the dum dum or sealant? I'd hate to buy a 10 meter roll just for the meter needed and trash the rest.
I think this is the fabric tape between the body shell, plastic washers and trim metal. I'm reusing mine.
Old 10-15-2015 | 07:37 PM
  #18  
Duck's Avatar
Duck
Burning Brakes
 
Joined: Nov 2006
Posts: 1,061
Likes: 3
From: Wilmington, NC USA
Default

Question is how difficult to put back in the windows. Tried putting those windows in a D.Moris hardtop and it is not easy. Still do not have them in (though I do not have an engine right now so not a big deal).
Old 10-16-2015 | 04:25 AM
  #19  
deutschland-dobson's Avatar
deutschland-dobson
Three Wheelin'
 
Joined: Jul 2009
Posts: 1,492
Likes: 3
From: NE England :)
Default

With the new seals the windows are a right **** to put back in.

You'll be looking a one person on the outside throwing their full bodyweight at it, whilst the second works the seal around from the inside, with string and a plastic scraper.

Chris
Old 10-16-2015 | 06:18 AM
  #20  
GeorgeK's Avatar
GeorgeK
Rennlist Member
 
Joined: Jan 2002
Posts: 654
Likes: 56
Default

Start at the front and make sure the rubber is deep enough in the frame. Then go with the bottom for a good seat and a water tight fit, then the rear tip and the top to finish.
Push HARD on the glass to get it as deep in its place as can be.
The glass may seem in place, with the lip in place, but can sit too proud in its opening, allowing for leaks and wind noises if it is not covered by the door window frame.
Old 01-16-2024 | 07:31 AM
  #21  
Alexd912's Avatar
Alexd912
Racer
 
Joined: Mar 2022
Posts: 270
Likes: 17
Default

Hey all,

I will be doing this job in the winter and have one question.

Can you not just use a knife and cut the rubber say from outside or inside and push the window out, then fit a new rubber?

Cheers
Alex


Old 01-16-2024 | 08:12 AM
  #22  
koenig_roland's Avatar
koenig_roland
Burning Brakes
 
Joined: Oct 2009
Posts: 1,050
Likes: 167
From: Mainhatten / Frankfurt
Default

Removed the rear windows last week.
I used such a set of plastic levers (correct wording?) from ebay for windows and clipsed parts from the car...

Took me 5min alone for one rear quarter window...
Old 01-16-2024 | 03:40 PM
  #23  
John McM's Avatar
John McM
Thread Starter
Rennlist Member
 
Joined: May 2001
Posts: 13,315
Likes: 652
From: Auckland, New Zealand.
Default

Originally Posted by Alexd912
Hey all,

I will be doing this job in the winter and have one question.

Can you not just use a knife and cut the rubber say from outside or inside and push the window out, then fit a new rubber?

Cheers
Alex
I put new rubber on and didn’t regret it, but the top edge by the door still annoys me. Original was closer to the body.
Old 01-17-2024 | 02:14 AM
  #24  
Alexd912's Avatar
Alexd912
Racer
 
Joined: Mar 2022
Posts: 270
Likes: 17
Default

I think the rubber has shrunk as there is a large gap from the very back of the window to the body.
So the rubber is junk IMHO so would replace it anyway, so I would assume it's just easier to cut it to get the window out.

As always I really appreciate all comments.

Alex




Quick Reply: How to remove a 964 rear quarter window



All times are GMT -3. The time now is 12:22 PM.