3 Liter Turbo Registry
#16
Addict
Rennlist Member
Rennlist Small
Business Sponsor
Rennlist Member
Rennlist Small
Business Sponsor
AN interesting note for 8v 3 liter builders - the 16v 3.0 engines have a harmonic damper built into the a/c alt pully and the 8v engine do not. The harmonic damper is a good idea to keep for the larger crank....
#17
Rennlist Member
Bore: 104.5
Stroke: 88
Pistons: Mahle/HMR 104.5 turbo pistons
Rods: Arrow Precision
Block: '94 968 3L
Head: '94 968 16V
Turbo: HMR
Engine Management: TECgt
Other: Siemens 83 #/hr injectors
The boost controller, an HKS EVC, was set for 1 bar (14.5 psi) maximum boost in this dyno run:
Stroke: 88
Pistons: Mahle/HMR 104.5 turbo pistons
Rods: Arrow Precision
Block: '94 968 3L
Head: '94 968 16V
Turbo: HMR
Engine Management: TECgt
Other: Siemens 83 #/hr injectors
The boost controller, an HKS EVC, was set for 1 bar (14.5 psi) maximum boost in this dyno run:
Last edited by Mike O; 01-02-2009 at 01:41 PM. Reason: Added dyno plot. Added boost setting
The following users liked this post:
ManOfTheHouse (11-04-2023)
#19
I have the long block below and an '87 951
Bore: 104.5 Stroke: 88
Pistons: Forged Mahle 968 std. pistons, top ring land machined for 427 Chevy moly rings, static compression ratio 8.71 : 1
Rods: New Carillo Racing Rods std. length, magnefluxed and measured for length and straightness
Block: 968 3.0
Head: 89 2.7
Turbo: TBD
Engine Management: Wolf
Other: JME CAM
I have a 968 tranny and Guard Transmission LSD. Time to buy a turbo and put it all together.
Pistons: Forged Mahle 968 std. pistons, top ring land machined for 427 Chevy moly rings, static compression ratio 8.71 : 1
Rods: New Carillo Racing Rods std. length, magnefluxed and measured for length and straightness
Block: 968 3.0
Head: 89 2.7
Turbo: TBD
Engine Management: Wolf
Other: JME CAM
I have a 968 tranny and Guard Transmission LSD. Time to buy a turbo and put it all together.
#20
Addict
Rennlist Member
Rennlist Member
I'm in the club..
Bore: 104.5 (no sleeve)
Stroke: 88
Pistons: Mahle/Andial 104.5 turbo pistons
Rods: Pauter
Block: 89 2.7 (added dual 993 squirters)
Head: 89 2.7
Turbo: Lindsey Super 75
Engine Management: VR
Other: web cam for now
Bore: 104.5 (no sleeve)
Stroke: 88
Pistons: Mahle/Andial 104.5 turbo pistons
Rods: Pauter
Block: 89 2.7 (added dual 993 squirters)
Head: 89 2.7
Turbo: Lindsey Super 75
Engine Management: VR
Other: web cam for now
#21
Rennlist Member
Thread Starter
Looks like we have similar motors. Have you been to a dyno?
#22
Addict
Rennlist Member
Rennlist Member
Yes, it did 386 at 17psi on a Mustang with a big boost leak. I'm heading back to the dyno probably around the first of the year. This first tunning session was for driveabiltiy. The next one will be for max hp. I may change the cam before I go back.
#23
Bore: 104.5 (no sleeve)
Stroke: 88
Pistons: Mahle/Andial 104.5 turbo pistons
Rods: PO-metal (Finland small manufacturer)
Block: 90? 3.0 (added squirters)
Head: 89 2.7
Turbo: Holset HX 40 Super
Engine Management: Tatech
Other: Dbilas 280' cam
Engine was "ready" august 2008, autumn drived with 13 psi, dynoed 430/550 from the crank.
Winter projects will be: large intercooler, repair of some minor oil leaks, new bearings for transaxle, LSD!!!!!
,Arto
Stroke: 88
Pistons: Mahle/Andial 104.5 turbo pistons
Rods: PO-metal (Finland small manufacturer)
Block: 90? 3.0 (added squirters)
Head: 89 2.7
Turbo: Holset HX 40 Super
Engine Management: Tatech
Other: Dbilas 280' cam
Engine was "ready" august 2008, autumn drived with 13 psi, dynoed 430/550 from the crank.
Winter projects will be: large intercooler, repair of some minor oil leaks, new bearings for transaxle, LSD!!!!!
,Arto
#24
Rennlist Member
Why don't we include any dyno charts / numbers as well? Do you have your numbers Tom?
My 3L motor with VR stage 5 turbo did 288whp at 9psi / 5500rpm which made me hopeful once the engine was run in.
My 3L motor with VR stage 5 turbo did 288whp at 9psi / 5500rpm which made me hopeful once the engine was run in.
#25
Rennlist Member
Arto, what do you mean dyno'd 430/550 from the crank? Are you saying at 13psi you're getting 550 hp at the crank??? No body will get near you! Even 430whp will take the record at that psi.
The following users liked this post:
ManOfTheHouse (11-04-2023)
#26
Drifting
Im hoping to get 400 at the wheels on 14 lbs. 104mm bore 88 stroke.
#27
Rennlist Member
Thread Starter
I only have this one so far. Still looking for a place that can run a dyno and its software...
#28
Bore: 104.5 (no sleeve)
Stroke: 88
Pistons: Mahle 104.5
Rods: PO-Metal
Block: '90 S2 (added squirters)
Head: ´89 2.7 (factory new)
Turbo: Holset (most likely)
Engine Management: VR (most likely)
Other: 944 n/a cam, but i am also considering Dbilas cam (Same kind as Arto is using)
Stroke: 88
Pistons: Mahle 104.5
Rods: PO-Metal
Block: '90 S2 (added squirters)
Head: ´89 2.7 (factory new)
Turbo: Holset (most likely)
Engine Management: VR (most likely)
Other: 944 n/a cam, but i am also considering Dbilas cam (Same kind as Arto is using)
#30
Rennlist Member
That's a good idea John. Have a list with each name having a link to the details of their car and numbers. I would think that it would take up too much space otherwise?