What have you done to your 944 S2 Cabriolet?
#751
Freedom Enthusiast
Rennlist Member
Rennlist Member
They won't fit in it when RSR VI comes up in another 4 years. It will be time for a Cayenne, Macan, or Panamera.
I have about another year or two before my middle son is too big for the back seat.
Macan Turbo's should have dropped a lot in price by then.
#755
Freedom Enthusiast
Rennlist Member
Rennlist Member
#756
Rennlist Member
haha, nothing really. i think your megasquirt system was the last thing, but hell you've done a lot more than me. I've got quite a bit of maintenance to do , but i haven't done anything but check out this thread and make wise cracks to you. my lazy ***.
#757
Freedom Enthusiast
Rennlist Member
Rennlist Member
Just don't do what I do. Break things!
I started installing my only944 shifter and I broke the plastic bushing the shift lever sits in. They are only a couple bucks but it puts me behind schedule. The replacement won't be here until Tuesday.
I can't find red bulbs that fit in the rear side marker housings so I am going to try to cover the existing bulbs with red lens repair tape. I'll see hot hot they get and how the tape holds up to the heat before I try to install them. I might go crazy and try to replace them with red LED's.
#758
Freedom Enthusiast
Rennlist Member
Rennlist Member
Well, It has started. The big summer project. I started tearing things down for the Microsquirt install. Intake is out(what a pain that was), Cam cover is off, time to start mapping the new wiring harness.
#759
Rennlist Member
you are my hero.
i'll get to it after i fix the h/g, brakes and shocks on my pickup, shocks on the a6, and brakes and shocks on the corolla. till then, i just don't park in anyones driveway and leave a stain.
i'll get to it after i fix the h/g, brakes and shocks on my pickup, shocks on the a6, and brakes and shocks on the corolla. till then, i just don't park in anyones driveway and leave a stain.
#761
Rennlist Member
you are pulling the 3.0 and swapping the 951 motor correct? getting married, so it will be a while before i get to any motor work. i may have lost the zeal for going the turbo/supercharged route. may just stick with N/A but move up to massaged 3.2L.
#762
Freedom Enthusiast
Rennlist Member
Rennlist Member
I picked up a set of wossner rods from a fellow RLer. I just bought a Garret GT3582R turbo from another RLer about 30 minutes ago. That will go to Forced Performance for their HTA turbo wheel upgrade. GeorgeD is getting positive pressure with his HTA GT3582 at idle. He says it is the fastest spooling turbo he has ever seen the doesn't fall off at high RPM's.
I am building a DIYPNP 55 pin Microsquirt system with a completely custom wiring harness.
Here is a list of the things I plan to get done in the next couple months(or more. The respray and turbo install may take a little longer)
DIYPNP 55 pin Microsquirt ECU.
It will be full sequential fuel and ignition.
1000 cc HiZ smartfire injectors
VW/Audi Coil on plug coils
044 fuel pump
3 bar FPR
MAP only, no MAF/AFM
Custom wiring harness
Custom intake
Koni adjustable front coilover kit
Camber plates
Elephant racing castor blocks
Weltmeister front sway bar
Braided steel brake lines
Euro front bumper cover
968 mirrors
Clear rear marker lenses
(I need to find some clear front turn signal lenses)
89 AOR LSD trans with cooler loop
only944 short shifter, shifter arm, and shift lever
New cam chain and tensioner pads
New powder coated cam cover
Eventually, some body work and a complete bare metal respray.
Last edited by azbanks; 06-24-2015 at 04:34 AM.
#763
Freedom Enthusiast
Rennlist Member
Rennlist Member
Cleaned the old oily gunk out of my intake ports.
Cleaned up the front timing cover for powder coating.
Install the factory lower shift lever bushing and finished installing the only944 shift lever.
Removed the factory coil since I won't be using it with the Megasquirt kit.
A few days ago I installed the SRPracing pedals.
http://www.srpracing.com/misc_images/SCBS1bu.jpg
Cleaned up the front timing cover for powder coating.
Install the factory lower shift lever bushing and finished installing the only944 shift lever.
Removed the factory coil since I won't be using it with the Megasquirt kit.
A few days ago I installed the SRPracing pedals.
http://www.srpracing.com/misc_images/SCBS1bu.jpg
#764
Rennlist Member
hey, i recognize those pedals.
you are definitely going all out. i remember the days of my wish list. so glad to finally close that file. now its just maintenance. hope you catch and tame that unicorn. i think real life caught up with me in terms of turbo engine build. driving my cousins supra showed me that boosting is gas drinking fun, but after the newness wore off and i wasn't running into people to race, i was just cruising around. it made me realize how i really drive my car. as a quick cruiser. i think i get the big speed rush from my sports bike.
still, i'll be a watchin'
you are definitely going all out. i remember the days of my wish list. so glad to finally close that file. now its just maintenance. hope you catch and tame that unicorn. i think real life caught up with me in terms of turbo engine build. driving my cousins supra showed me that boosting is gas drinking fun, but after the newness wore off and i wasn't running into people to race, i was just cruising around. it made me realize how i really drive my car. as a quick cruiser. i think i get the big speed rush from my sports bike.
still, i'll be a watchin'
#765
Freedom Enthusiast
Rennlist Member
Rennlist Member
The deal on the gt3582 fell through. I am really really bummed out!!!!!!!
I would love to have a sport bike if all the other drivers in Phoenix would agree to stay off the roads when I am on it.
I would love to have a sport bike if all the other drivers in Phoenix would agree to stay off the roads when I am on it.