Wrenching Open House
#1
Rennlist Member
Thread Starter
Wrenching Open House
Hey fellow shark tank residents.
This weekend is going to be a big re-assembly weekend. My family is away for another week so I'm spending every extra minute in the garage.
Feel free to pop by to check out my progress or lend a hand if you want. Plenty of cold beer in the fridge. Or just watch, it's all good.
This weekend I will be putting on my new belt, water pump, tensioner, powder coated intake, cam covers, water bridge, oil filler neck, plugs and wires, knock sensors, injectors etc.
Text nine zero five-4six4-235three
Adam
This weekend is going to be a big re-assembly weekend. My family is away for another week so I'm spending every extra minute in the garage.
Feel free to pop by to check out my progress or lend a hand if you want. Plenty of cold beer in the fridge. Or just watch, it's all good.
This weekend I will be putting on my new belt, water pump, tensioner, powder coated intake, cam covers, water bridge, oil filler neck, plugs and wires, knock sensors, injectors etc.
Text nine zero five-4six4-235three
Adam
Last edited by Adamant1971; 01-09-2014 at 03:46 PM.
#2
Take lots of pictures to share with those who aren't close enough to lend a hand.
#3
Rennlist Member
Thread Starter
I will. Can't wait to see it finished.
#5
Rennlist Member
If I have a chance I will drop in to visit(Sunday) and hope to lend a helping hand if necessary.
You have a fantastic 928 S4 with all the goodies! Sport seats, manaul transmission, LSD and more.
You have a fantastic 928 S4 with all the goodies! Sport seats, manaul transmission, LSD and more.
#6
Rennlist Member
Thread Starter
Cool Mike, just text me.
All the parts are here and I just picked up the parts from the powder coater.
Woo Hoo
All the parts are here and I just picked up the parts from the powder coater.
Woo Hoo
Last edited by Adamant1971; 12-11-2022 at 04:27 PM.
Trending Topics
#9
Rennlist Member
Thread Starter
#10
Rennlist Member
Thread Starter
This should keep me busy.
Last edited by Adamant1971; 12-11-2022 at 04:27 PM.
#11
Team Owner
looks like your doing a great job, I would suggest to make sure wash the intake atleast three times with car soap and hot water, and a tooth brush
then blow dry with compressed air,
This may seem redundant BUT if the intake was grit blasted then it will have grit inside it.
also chase the bolt holes with a tap and clean the holes they will also have grit.
Goodluck on your project
then blow dry with compressed air,
This may seem redundant BUT if the intake was grit blasted then it will have grit inside it.
also chase the bolt holes with a tap and clean the holes they will also have grit.
Goodluck on your project
#12
Intermediate
Hello Adam,
Are noob's welcome, dumbass questions and all.
I'd like to see the front end of the engine opened up, seeing as I'm due to check belt tension soon ( tb/wp replaced by PO just before I purchased car). What stage do you think you'd be at Sunday - not that I'm holding you to it - just a guess.
Cheers, Peter Hendriks
Are noob's welcome, dumbass questions and all.
I'd like to see the front end of the engine opened up, seeing as I'm due to check belt tension soon ( tb/wp replaced by PO just before I purchased car). What stage do you think you'd be at Sunday - not that I'm holding you to it - just a guess.
Cheers, Peter Hendriks
#13
Rennlist Member
Nice powder coat job ... and good to see someone else who makes proper use of all domestic areas for parts layout ... you'll find that dishwashers, ovens, trays, and lots of kitchen utensils are also great for mechanical work
#14
Rennlist Member
Thread Starter
Thanks for the help today, Pete r and Livio. It was nice to shoot the breeze and get her buttoned up.
Last edited by Adamant1971; 12-11-2022 at 04:27 PM.