Notices
928 Forum 1978-1995
Sponsored by:
Sponsored by: 928 Specialists

Where does this connect?

Thread Tools
 
Search this Thread
 
Old Feb 2, 2005 | 06:04 AM
  #1  
Airflite40's Avatar
Airflite40
Thread Starter
Official Rennlist
Borat Impersonator
Rennlist Member
20 Year Member
 
Joined: Sep 2003
Posts: 5,018
Likes: 37
From: St Augustine, FL
Default Where does this connect?

I am kind confused about where this part connects to. The two brown wires shown below connect to the WUR and sup. Air Valve via the black connectors, but the other ends of the brown wires come together into a circular loop connector. It says in the wire diagram that it goes to the fuel pump, but where does it connect? I think it is the wires shown below, I borrowed this pic from BigDave's thread. I hope that's okay, I don't want to jack his thread. Thanks!
Attached Images
File Type: jpg
engineout51.JPG (66.2 KB, 167 views)
File Type: jpg
question.JPG (6.2 KB, 180 views)
Reply
Old Feb 2, 2005 | 07:54 AM
  #2  
SharkSkin's Avatar
SharkSkin
Rennlist Member
 
Joined: Jan 2004
Posts: 12,620
Likes: 8
From: Boulder Creek, CA
Default

Brown wires = Ground. The wiring diagram that you show the snippet of is for 79, and on that diagram the connection to the fuel pump relay is shown as an internal connection, inside the fuse panel. The bottom line in the diagram is always ground.
Reply
Old Feb 2, 2005 | 10:19 AM
  #3  
Airflite40's Avatar
Airflite40
Thread Starter
Official Rennlist
Borat Impersonator
Rennlist Member
20 Year Member
 
Joined: Sep 2003
Posts: 5,018
Likes: 37
From: St Augustine, FL
Default

So, where would they connect, the jump terminal?
Reply
Old Feb 2, 2005 | 02:01 PM
  #4  
Scott M.'s Avatar
Scott M.
Rest in Peace
Rennlist Member
 
Joined: Apr 2003
Posts: 2,240
Likes: 0
From: Penn State
Default

Borys;

The picture is of a 5.0L engine, your wire diagram is for a CIS car...

I assume the picture is just for reference purposes only and your asking about you 80 Euro...

From what I can gather your asking, the two brown wires that come together are ground wires (which come out of the main harness) that bolt to the back of the timing belt cover where the black plastic meets the aluminum.

Scott
Reply
Old Feb 2, 2005 | 02:28 PM
  #5  
Airflite40's Avatar
Airflite40
Thread Starter
Official Rennlist
Borat Impersonator
Rennlist Member
20 Year Member
 
Joined: Sep 2003
Posts: 5,018
Likes: 37
From: St Augustine, FL
Default

Great Scott! That makes sense. Thanks!!!
Reply
Old Feb 2, 2005 | 02:30 PM
  #6  
SharkSkin's Avatar
SharkSkin
Rennlist Member
 
Joined: Jan 2004
Posts: 12,620
Likes: 8
From: Boulder Creek, CA
Default

Scott's right... they should connect to ground(as I said before). I'll take a look later and see if I can figure out where they connect exactly. Below is the only pic I seem to have that shows them:

Reply
Old Feb 2, 2005 | 02:43 PM
  #7  
Airflite40's Avatar
Airflite40
Thread Starter
Official Rennlist
Borat Impersonator
Rennlist Member
20 Year Member
 
Joined: Sep 2003
Posts: 5,018
Likes: 37
From: St Augustine, FL
Default

Ok ok you were right too Dave
Reply
Old Feb 2, 2005 | 02:43 PM
  #8  
Airflite40's Avatar
Airflite40
Thread Starter
Official Rennlist
Borat Impersonator
Rennlist Member
20 Year Member
 
Joined: Sep 2003
Posts: 5,018
Likes: 37
From: St Augustine, FL
Default

BTW, whats up with your shark? no round 19 yet? Your site is awesome!
Reply
Old Feb 2, 2005 | 02:57 PM
  #9  
SharkSkin's Avatar
SharkSkin
Rennlist Member
 
Joined: Jan 2004
Posts: 12,620
Likes: 8
From: Boulder Creek, CA
Default

I've been doing lots of little stuff, no time to update. It's coming...

And thanks!
Reply




All times are GMT -3. The time now is 02:31 AM.