RacingBrakes.com products are amazing!
#1
Rennlist Member
Thread Starter
RacingBrakes.com products are amazing!
Putting on the RacingBrakes.com Rotors on my race car has been one of the best mods yet. now, instead of them cracking out in a half of a season, they last a full 2 seasons
it has to do with their metalurgy and casting methods. (horizontal vs vertical as most common suppliers use). this provides strength and wear consistancy that i havent seen before on any cars i race with.
they have a 2 piece design for every need (sans the early cars) . this means you can use a stock caliper and run the stock rotors with 2 piece design, bump it up to a GTS diameter (322mm) or go a little bigger and use the 330 or even 332mm rotors...........the only mod if you have an S4, would be to use simple washers (machined spacers) to push out the calipers the appropriate amount for an S4 to use a 330mm rotor or a GTS to use a 330 or 332 mm rotor.
im going to cal speedway with these rotors for their last race after providing 2 full racing seasons on the front of my race car. they might be good for longer but i dont want to take any chances and have bought new rotor rings for the remainder of the season. This is my 3rd set of the rings in the past few years and they work great. one of the side benifits of the Rotors , is the cost. big advantage over Brembo and brembo equivalent set ups and its better. check out the link for versions available to use as 928'ers.
http://www.racingbrake.com/category-s/7365.htm
RB rotor rings
the brembo, older RB and new RB rotors air inlet designs
330mm rotors on the car using the stock S4 style calipers
old vs new RB designs since 2 years ago
http://www.racingbrake.com/category-s/7365.htm
it has to do with their metalurgy and casting methods. (horizontal vs vertical as most common suppliers use). this provides strength and wear consistancy that i havent seen before on any cars i race with.
they have a 2 piece design for every need (sans the early cars) . this means you can use a stock caliper and run the stock rotors with 2 piece design, bump it up to a GTS diameter (322mm) or go a little bigger and use the 330 or even 332mm rotors...........the only mod if you have an S4, would be to use simple washers (machined spacers) to push out the calipers the appropriate amount for an S4 to use a 330mm rotor or a GTS to use a 330 or 332 mm rotor.
im going to cal speedway with these rotors for their last race after providing 2 full racing seasons on the front of my race car. they might be good for longer but i dont want to take any chances and have bought new rotor rings for the remainder of the season. This is my 3rd set of the rings in the past few years and they work great. one of the side benifits of the Rotors , is the cost. big advantage over Brembo and brembo equivalent set ups and its better. check out the link for versions available to use as 928'ers.
http://www.racingbrake.com/category-s/7365.htm
RB rotor rings
the brembo, older RB and new RB rotors air inlet designs
330mm rotors on the car using the stock S4 style calipers
old vs new RB designs since 2 years ago
http://www.racingbrake.com/category-s/7365.htm
#2
Rennlist Member
Join Date: Nov 2017
Location: York, PA
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
I've dealt with them before, neat place if you can stop by.
I forget the guys name I was working with, a super nice older gentleman.
The do it right, that's for sure,
I forget the guys name I was working with, a super nice older gentleman.
The do it right, that's for sure,
#3
Rennlist Member
Thread Starter
they told me the entire story.. it makes sense for why ive gotten the life out of them after destroying stock rotors in short order, which is tough to do. the horizontal casting is a key component. I think you are talking about Warren. his background is this kind of technology.......seems they are doing it right. i might even switch to the center mount style of hats and put mine up for sale.
#7
Rennlist Member
Thread Starter
Why do you think that? A few of the options are not even available yet, I thought Roger just had the stock stuff for the braking system.
ok, I'll fall for it.... How big ARE your brakes!
ok, I'll fall for it.... How big ARE your brakes!
Trending Topics
#8
Rennlist Member
Mark, how much did you pay for two rotors?
The listed non-sale price is $900; that's like, a million dollars more than stock rotors!
The listed non-sale price is $900; that's like, a million dollars more than stock rotors!
#9
Rennlist Member
Thread Starter
you only replace the Rings if they ever wear out. on a street car, i have a hard time imagining that they will ever wear out , based on what ive seen. even if you track it a few times a year.
in the end, you also end up having a complete big brake set up, with NO change in calipers. you get the 2 piece rotor set up which looks good too and you get performance increases if you track the car as well.
#10
Inventor
Rennlist Member
Rennlist Member
You don't have to machine (or Kibort grind) a S4 caliper for the larger radius?
#11
Rennlist Member
I have Big Reds from a 993TT on the front which are 2-piece with hats. I did not see an option for just replacement rotors.
#12
Administrator - "Tyson"
Lifetime Rennlist
Member
Lifetime Rennlist
Member
http://www.racingbrake.com/Rotor-rin...021-311k-b.htm
Not sure these are the correct ones, just searched for 330mm
#13
Rennlist Member
In this configuration they are just called "rotor rings"
http://www.racingbrake.com/Rotor-rin...021-311k-b.htm
Not sure these are the correct ones, just searched for 330mm
http://www.racingbrake.com/Rotor-rin...021-311k-b.htm
Not sure these are the correct ones, just searched for 330mm
#14
Rennlist Member
Thread Starter
yes, you do need to do a little grind on the S4 calipers for the 322mm rotors (which are the GTS diameter). very minor though
with the 330mm, it was a little extreme.. i did it, but it wasnt optimal.
However, when switching to the 964 turbo calipers, you get a S4 Pad caliper, but the feet on the caliper have built in spacers, (taller) and they are radiused as well too. basically, you get a GTS caliper that is not as deep and uses S4 pads.
whatever your combination , RB.com can provide the rotor and hat combo.
#15
Rennlist Member
Thread Starter
what do they look like? are they the Brembo rings you use to mate to the hat? if so, that rotor is the same diameter as the GTS, 322mm, right? if it is a brembo ring, i think they have the replacements, and you can do what i did , by just using spacers and then using the brembo 332mm ring to get even MORE rotor diameter.