Can I use my transmission cooler for engine oil?
#1
Rennlist Member
Thread Starter
Can I use my transmission cooler for engine oil?
Hello all:
I converted my automatic car to a 5 speed some years ago and still have the stock radiator with an automatic transmission side.
While I haven't had any overheating issues since my twinscrew install I'd like to take advantage of any additional capacity that I can.
So, my question is; would it be possible and advisable to make an extra set of lines and use the transmisssion cooler side of my radiator for additional engine oil cooling?
If the above is possible, would I sacrifice the water cooling ability of the radiator by adding back in this extra load.
Thanks,
Ken
I converted my automatic car to a 5 speed some years ago and still have the stock radiator with an automatic transmission side.
While I haven't had any overheating issues since my twinscrew install I'd like to take advantage of any additional capacity that I can.
So, my question is; would it be possible and advisable to make an extra set of lines and use the transmisssion cooler side of my radiator for additional engine oil cooling?
If the above is possible, would I sacrifice the water cooling ability of the radiator by adding back in this extra load.
Thanks,
Ken
#2
Drifting
Join Date: Nov 2001
Location: zürich, switzerland
Posts: 2,233
Likes: 0
Received 0 Likes
on
0 Posts
HTML Code:
would it be possible and advisable to make an extra set of lines and use the transmisssion cooler side
HTML Code:
would I sacrifice the water cooling ability of the radiator
Marton
#5
Nordschleife Master
If you have a twin screw I would find a way to pump the gearbox fluid through that cooler, similiar to the GTS cars. You already have hardlines running on the underside of the car, you would need to find a location to pull from the G28 box amd likewise to return to, (although You could probably use the front drain plug and the top, breather area as your return) and get a small electric oil pump. You wont have the efficency of the GTS unit as i believe there are squirters directly onto the gears but it would increase your transaxle capacity by nearly 2L and would be great if you drive the **** out of it.
#6
Drifting
Join Date: Nov 2001
Location: zürich, switzerland
Posts: 2,233
Likes: 0
Received 0 Likes
on
0 Posts
HTML Code:
Oil cooler hoses to rad are larger than trans. It is possible to slow down oil flow.
I copied this picture from the Behr site, I hoped it would give dimensions for the engine & transmission oil coolers but there is nothing written. The connections for the 2 coolers look very similar but I do not know how accurate is the drawing...
Marton
#7
Drifting
Join Date: Nov 2001
Location: zürich, switzerland
Posts: 2,233
Likes: 0
Received 0 Likes
on
0 Posts
If you follow Ryans suggestion about cooling the gear box and you are still worried about engine oil temp you could always add an extra external engine oil cooler?
Marton
Marton
Trending Topics
#9
Instructor
Join Date: Jun 2003
Location: Pittsburgh, PA
Posts: 102
Likes: 0
Received 0 Likes
on
0 Posts
I tried to do this after converting to a Devek Radiator with no cooler. I bought an external automatic transmission oil cooler off of a 928 and planned to use that as an external oil cooler. The fittings are significantly smaller than that of the oil cooler. Offhand I would say about 1/2 the size. I was worried that this would restrict flow significantly so I went with an external oil cooler with proper sized fittings.
#11
Rennlist Member
Thread Starter
Good feed back guys.....
I may just go with a MoCal and mount it up front with the heat exchangers for the intercooler.
As for the tranny, if I go with a cooler back there I would probably just mount a cooler in a horizontal position with a small designated fan.
Thanks for all of the replies.
Ken
I may just go with a MoCal and mount it up front with the heat exchangers for the intercooler.
As for the tranny, if I go with a cooler back there I would probably just mount a cooler in a horizontal position with a small designated fan.
Thanks for all of the replies.
Ken
#12
Nordschleife Master
The radiator is already cooling the oil since the oil is running through the same aluminum block as the coolant. It has at least some risk of harm, and little to gain.
Before doing any plumbing I would measure the temperature to see if its warranted. Air ducting might be better than a external cooler too.
Before doing any plumbing I would measure the temperature to see if its warranted. Air ducting might be better than a external cooler too.
#13
Nordschleife Master
if you want an external oil cooler buy the 90+ porsche item. I paid I think $305 for it new, it mounts just below the radiator. Use that for oil. Use the trans cooler above the rad to cool the transaxle oil, or just remove it.
#14
Rennlist Member
Thread Starter
"The radiator is already cooling the oil since the oil is running through the same aluminum block as the coolant. It has at least some risk of harm, and little to gain."
Danglerb
I don't understand what difference this would make as one "end" of the radiator is already circulating engine oil. I would be employing both "ends".
"Use the trans cooler above the rad to cool the transaxle oil, or just remove it.
Ryan
The cooler is integral to the radiator and not an external cooler.
Danglerb
I don't understand what difference this would make as one "end" of the radiator is already circulating engine oil. I would be employing both "ends".
"Use the trans cooler above the rad to cool the transaxle oil, or just remove it.
Ryan
The cooler is integral to the radiator and not an external cooler.
#15
Nordschleife Master
Oh,
Is the cooler above the radiator and below the intake ducts one piece with the radiator assembly? I didnt know, manual cars before 92 dont have that. I figured it would be a different part.
Regardless, I wouldnt run oil through it, your radiator is your oil cooler it runs through a tank inside the end cap of the rad. If anything you would reduce circulation of the already effective engine oil cooler and also have the potential for more oil leaks with the additional lines you want to run.
Is the cooler above the radiator and below the intake ducts one piece with the radiator assembly? I didnt know, manual cars before 92 dont have that. I figured it would be a different part.
Regardless, I wouldnt run oil through it, your radiator is your oil cooler it runs through a tank inside the end cap of the rad. If anything you would reduce circulation of the already effective engine oil cooler and also have the potential for more oil leaks with the additional lines you want to run.