Rennlist - Porsche Discussion Forums
0 2025/04/21 18:36:21
0 2025/04/21 18:39:10
0 2025/04/22 21:18:57
0 2025/04/22 21:19:54
0 2025/04/22 21:19:57
Again, would've mounted 1/3" higher since I didn't use the tightening collar. But still works fine as is.
Again, would've mounted 1/3" higher since I didn't use the tightening collar. But still works fine as is.
0 2025/04/22 21:20:00
0 2025/04/22 21:20:02
0 2025/04/22 21:20:05
0 2025/04/22 21:20:07
0 2025/04/22 21:20:09
0 2025/04/22 21:20:11
Without quad lock, 1/4-20 threads ready for another mounting system.
Without quad lock, 1/4-20 threads ready for another mounting system.
0 2025/04/22 21:20:14
0 2025/04/22 21:20:17
0 2025/04/25 07:29:28
0 2025/04/25 07:29:42
0 2025/04/25 07:29:45
0 2025/04/25 07:29:48
0 2025/08/31 07:30:20
0 2025/08/31 07:30:23
0 2025/08/31 07:30:27
0 2025/08/31 07:29:57
0 2025/08/31 07:29:33
It is long to fit deeper gt3 bumper, so i trimmed it after in mounted it up. The other bit is the trimming in diff on the corner trim on bottom side of bumper in front of wheel well. It wasn't necessary, but it fit just a bit better this way
It is long to fit deeper gt3 bumper, so i trimmed it after in mounted it up. The other bit is the trimming in diff on the corner trim on bottom side of bumper in front of wheel well. It wasn't necessary, but it fit just a bit better this way
0 2025/08/31 07:30:10
0 2025/08/31 07:30:13
The overlap of the corner plastic i trimmer for the splitter to sit a little more flush over
The overlap of the corner plastic i trimmer for the splitter to sit a little more flush over
0 2025/08/31 07:30:17
0 2025/08/31 07:29:37
0 2025/08/31 07:29:47
0 2025/08/31 07:30:00
0 2025/08/31 07:30:35
0 2025/08/31 07:33:07
First autoX after mounting it! No cone hits but it would def do fine. Its beefy but not brittle.
First autoX after mounting it! No cone hits but it would def do fine. Its beefy but not brittle.
0 2025/08/31 07:33:15
0 2025/08/31 07:33:18
0 2025/08/31 07:33:21
0 2025/08/31 07:33:24
I used these preexisting holes in my bumper to index the splitter off of. It worked great. I had to drill a hole in the metal recess that is part of the radiator and wheel well bracket and tapped it with m6x1.0 threads for the long stainless bolt you see.
I used these preexisting holes in my bumper to index the splitter off of. It worked great. I had to drill a hole in the metal recess that is part of the radiator and wheel well bracket and tapped it with m6x1.0 threads for the long stainless bolt you see.
0 2025/08/31 07:38:19
0 2025/08/31 07:38:27
After drilling/mounting a couple fasteners i noticed the lip wasnt flush using the pre existing holes on the spoiler. So i used them as guides but drilled my own holes further forward on the splitter. It worked great. You'll see this on the others photos better.
After drilling/mounting a couple fasteners i noticed the lip wasnt flush using the pre existing holes on the spoiler. So i used them as guides but drilled my own holes further forward on the splitter. It worked great. You'll see this on the others photos better.
0 2025/08/31 07:42:42
0 2026/03/12 09:30:17
0 2026/03/12 09:30:44
0 2026/03/12 09:30:47