FS: 1986 Porsche 944 Turbo GT3S for sale
#1
Addict
Rennlist Member
Rennlist Member
Thread Starter
Join Date: Mar 2009
Location: Montreal
Posts: 2,193
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
1986 Porsche 944 Turbo GT3S for sale
20 000$, O.B.O.
Ran 2:08 at WGI, ran 1:31 at Mosport, and 1:48 at Tremblant.
PCA Log book,
Varac class winner at Tremblant
Body:
105 000 miles on the body. Was repainted (base coat + clear) in 2007;
Full roll cage + window nets;
Kirkey aluminium race seat and Sparco belts on Recaro sliders;
DP motorsport front splitter;
Solid engine mount;
Solid trans mount;
New bearings everywhere;
Quick release Momo wheel;
Inboard manual boost controller;
Manual steering rack;
3 piece cross member;
AMB transponder;
Short shift kit;
Weights approximately 2600Lbs;
Suspension:
New Penske shocks (rear), Anze/Penske Struts (front), 2 way adjustable (remote canisters);
Custom A-arms;
Camber plates;
Strut tower brace;
Front and rear weltmeister adjustable sway bars;
Solid bushings everywhere.
Engine: brand new engine built for 2010, approximately 12 hours on it
Steel sleeved, new aftermarket pistons, shotpeened rods, Fiorano head, piston squirters, lightened knife-edge crank and so on;
Custom oil cooler;
Turbonetics Turbo (2 seasons on it) + heat shield;
Vitesse MAF;
Webcam;
SFR 4 into 1 headers (321SS) ceramic coated + 2 piece cross-over pipe + downpipe;
SFR Hard pipes;
SFR intercooler;
Tial 38mm wastegate;
Tial BOV;
New SS fuel lines;
Adjustable fuel pressure regulator;
4 inches exhaust system;
3 years old rad, new temp sensor;
New fuel pump;
Brakes:
New big black calipers and rotors;
New master cylinder (89) + BPV;
Nearly new PF pads;
New rotor at the front and back back;
Wheels:
1 set of Fikse 9 x 17 and 10 x 17 with Hoosiers R6;
1 set of Jongbloed 9 x 17 and 10 x 17 with Hoosiers R6
Regular maintenance:
Mostly anything that had to break was replaced. Think of it and I did it.
What has to be done:
Original aluminium turbo heat shield has to be put back in place;
Small dent in the left front fender, bumper + fender covered with racer’s tape, paint will be needed at some point;
There is some head work to be done, will be taken care of before delivery.
Adding a plastic rear window would bring the car closer to the weight limit. Performance Index is currently at 569 (GT-3) with a 220 lbs driver and ½ tank of gas. Or add a few pounds and move to GT-4.
20 000$, O.B.O.
Ran 2:08 at WGI, ran 1:31 at Mosport, and 1:48 at Tremblant.
PCA Log book,
Varac class winner at Tremblant
Body:
105 000 miles on the body. Was repainted (base coat + clear) in 2007;
Full roll cage + window nets;
Kirkey aluminium race seat and Sparco belts on Recaro sliders;
DP motorsport front splitter;
Solid engine mount;
Solid trans mount;
New bearings everywhere;
Quick release Momo wheel;
Inboard manual boost controller;
Manual steering rack;
3 piece cross member;
AMB transponder;
Short shift kit;
Weights approximately 2600Lbs;
Suspension:
New Penske shocks (rear), Anze/Penske Struts (front), 2 way adjustable (remote canisters);
Custom A-arms;
Camber plates;
Strut tower brace;
Front and rear weltmeister adjustable sway bars;
Solid bushings everywhere.
Engine: brand new engine built for 2010, approximately 12 hours on it
Steel sleeved, new aftermarket pistons, shotpeened rods, Fiorano head, piston squirters, lightened knife-edge crank and so on;
Custom oil cooler;
Turbonetics Turbo (2 seasons on it) + heat shield;
Vitesse MAF;
Webcam;
SFR 4 into 1 headers (321SS) ceramic coated + 2 piece cross-over pipe + downpipe;
SFR Hard pipes;
SFR intercooler;
Tial 38mm wastegate;
Tial BOV;
New SS fuel lines;
Adjustable fuel pressure regulator;
4 inches exhaust system;
3 years old rad, new temp sensor;
New fuel pump;
Brakes:
New big black calipers and rotors;
New master cylinder (89) + BPV;
Nearly new PF pads;
New rotor at the front and back back;
Wheels:
1 set of Fikse 9 x 17 and 10 x 17 with Hoosiers R6;
1 set of Jongbloed 9 x 17 and 10 x 17 with Hoosiers R6
Regular maintenance:
Mostly anything that had to break was replaced. Think of it and I did it.
What has to be done:
Original aluminium turbo heat shield has to be put back in place;
Small dent in the left front fender, bumper + fender covered with racer’s tape, paint will be needed at some point;
There is some head work to be done, will be taken care of before delivery.
Adding a plastic rear window would bring the car closer to the weight limit. Performance Index is currently at 569 (GT-3) with a 220 lbs driver and ½ tank of gas. Or add a few pounds and move to GT-4.
Last edited by Charles A. Toupin; 03-01-2012 at 04:44 PM. Reason: precision
Trending Topics
#8
Addict
Rennlist Member
Rennlist Member
Thread Starter
Join Date: Mar 2009
Location: Montreal
Posts: 2,193
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Friday morning bump - make me an offer the car has to move out of the garage.
Price reduced to 18 995$ O.B.O.
The 2 sets of custom wheels and tires + the Penske shocks are worth the asking price.
Imagine, you get the rest of the car for FREE!!!!!!!!!!!!!!
![Big Grin](https://rennlist.com/forums/images/smilies/biggrin.gif)
c.
Price reduced to 18 995$ O.B.O.
The 2 sets of custom wheels and tires + the Penske shocks are worth the asking price.
Imagine, you get the rest of the car for FREE!!!!!!!!!!!!!!
![Big Grin](https://rennlist.com/forums/images/smilies/biggrin.gif)
c.