PORSCHE Decal for GT3 Wing
12-09-2017, 04:10 AM
#31
03-20-2018, 02:01 PM
#32
IDK, w the aluminum wheels, I think I would like a bunch of tastefully low-key accents to match. If i did hood/ roof stripes, i'd probably do a thin single one the width of the porsche crest on the hood, and for sides, the "porsche" on the door in a light grey w black stripes... Just get the color correct!
The following users liked this post:
Esov (03-11-2021)
11-21-2018, 05:36 PM
#33
Rennlist Member
Reviving an older thread with hopes for some pointers.
I am looking for a place to source the small "4.0" decal that would go on to the side small piece of the 991.2 GT3 wing. Basically the engraved section on the rectangular panel on the upright.
Did a similar thing on my GT4 (by the side intakes), so looking to do the same here (in yellow). TIA
I am looking for a place to source the small "4.0" decal that would go on to the side small piece of the 991.2 GT3 wing. Basically the engraved section on the rectangular panel on the upright.
Did a similar thing on my GT4 (by the side intakes), so looking to do the same here (in yellow). TIA
Last edited by Dr. Ferdinand; 11-21-2018 at 05:52 PM.
11-21-2018, 11:10 PM
#34
Race Director
Thread Starter
Reviving an older thread with hopes for some pointers.
I am looking for a place to source the small "4.0" decal that would go on to the side small piece of the 991.2 GT3 wing. Basically the engraved section on the rectangular panel on the upright.
Did a similar thing on my GT4 (by the side intakes), so looking to do the same here (in yellow). TIA
I am looking for a place to source the small "4.0" decal that would go on to the side small piece of the 991.2 GT3 wing. Basically the engraved section on the rectangular panel on the upright.
Did a similar thing on my GT4 (by the side intakes), so looking to do the same here (in yellow). TIA
11-21-2018, 11:54 PM
#35
Rennlist Member
Thanks Jimmy - I had looked them up prior, but they do not have it featured on their website.
Just to clarify, not looking for the end plates like so: https://kistudios.com/product/porsch...ng-end-decals/
Rather, what I am looking for is the trapeziod-ish trim piece/panel on the vertical upright, that has the indented "4.0" italic script. Hence similar to the "GT4" on the side intake blade.
Just to clarify, not looking for the end plates like so: https://kistudios.com/product/porsch...ng-end-decals/
Rather, what I am looking for is the trapeziod-ish trim piece/panel on the vertical upright, that has the indented "4.0" italic script. Hence similar to the "GT4" on the side intake blade.
11-22-2018, 02:53 AM
#36
Rennlist Member
Thanks Jimmy - I had looked them up prior, but they do not have it featured on their website.
Just to clarify, not looking for the end plates like so: https://kistudios.com/product/porsch...ng-end-decals/
Rather, what I am looking for is the trapeziod-ish trim piece/panel on the vertical upright, that has the indented "4.0" italic script. Hence similar to the "GT4" on the side intake blade.
Just to clarify, not looking for the end plates like so: https://kistudios.com/product/porsch...ng-end-decals/
Rather, what I am looking for is the trapeziod-ish trim piece/panel on the vertical upright, that has the indented "4.0" italic script. Hence similar to the "GT4" on the side intake blade.
Was looking for the same. Contacted a cple places and they said get a piece of paper and a crayon( take the wrapping off). Lay the paper over the 4.0 and etch it or shade over top so you get the exact trace w the crayon on its side. Then send it to Kistudios or whoever so they can make it the exact size. Just havnt got around to it. Im sure if someone does this and somone starts making these 4.0 inlays. A lot will sell. I had a GT4 as well w the same inlays on the vents.
11-22-2018, 07:30 AM
#38
Race Director
Thread Starter
Thanks Jimmy - I had looked them up prior, but they do not have it featured on their website.
Just to clarify, not looking for the end plates like so: https://kistudios.com/product/porsch...ng-end-decals/
Rather, what I am looking for is the trapeziod-ish trim piece/panel on the vertical upright, that has the indented "4.0" italic script. Hence similar to the "GT4" on the side intake blade.
Just to clarify, not looking for the end plates like so: https://kistudios.com/product/porsch...ng-end-decals/
Rather, what I am looking for is the trapeziod-ish trim piece/panel on the vertical upright, that has the indented "4.0" italic script. Hence similar to the "GT4" on the side intake blade.
11-25-2018, 09:57 PM
#40
Rennlist Member