When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Are you sure those are Brey Krause sliders? They look like factory GT3 hard back sliders with Brey krause sub belt cross bars. Either case this is the deal of the year. Just one of the sub bar mounts are $121 new not including the other and both sliders. These would cost you close to $600 or more new.
If I didn't just spend a fortune installing recaro sliders and same sub mount bars i would be all over these.
Misc 964 tan interior bits taken from 90 C2. What you see is what you get---almost. Two rear seat bottom cushions (far left) are gone. Sorry. Prefer to sell as a lot. No rips or tears, but some pieces are dirty/faded. $75 plus shipping to lower 48. Leaves and pine needles are extra.
Perfect for a project car. Or for mice and squirrels to build a winter bungalow. Save it from that fate....
Update: tired of tripping over these and yelling at dog to not lift his leg and take a leak. $75 plus shipping or you pick up. Otherwise, they go in next Tuesday's garbage.
Bumping an earlier post of mine from previous page. This stuff is on Death Row. It either escapes my garage El Chapo style, or is given the needle. Please save it from the trash heap....
For those of you that have upgraded to Big Reds up front and 993 rear brakes, I'm selling a set of pagid sport pads that were on my car for less than 50 miles. I couldn't take the squealing so I opted to have OEM pads instead. $250 shipped. PM if interested. Thanks.
Bumping an earlier post of mine from previous page. This stuff is on Death Row. It either escapes my garage El Chapo style, or is given the needle. Please save it from the trash heap....
The prisoner has escaped. On its way to NJ. Thanks Anthony!!!
Have the full set of OEM RS engine mounts. Also got Wevo's, so deciding which to go with. If someone here wants the RS mounts and all the required assembly items, happy to part with it for $425.
Have the full set of OEM RS engine mounts. Also got Wevo's, so deciding which to go with. If someone here wants the RS mounts and all the required assembly items, happy to part with it for $450.
S CAR GO headers, RUF speedlines 18", GT3 muffler, 993TT crank, Carillo rods
S CAR GO Equal Length, long tube headers
25" long, 1-3/4" primaries with 2.5" V-band connectors for Naturally Aspirated 911 air cooled engines.
I believe they are the same headers used by Singer on the green car.
There were used on a 964 3.6 L engine but is should be compatible with most air cooled applications (would also fit 993)
They were used by a customer for 30 min on a chassis dyno. The customer ended up wanting heat instead, so he had to change exhaust systems.
16ga 304S stainless steel tubing, TIG welded, Slip tubes into beautiful merge collectors with straps.
O2 sensor ports on both collectors if needed.
Front: 8.5J x 18 with a ET61
Rear: 9.5J x 18 ET48.3
Excellent condition - Painted gloss back with red lips
There are some small chips in the red lips but no curbing. One wheel has a few chips in the black paint but nothing major. I imagine most people would refinish the wheels to their own liking, however they are painted nicely enough that if you like the colorway you could run them as-is. There are no bends or damage from what I can tell. Porsche center caps painted to match. I would consider trades for other 17" or 18" wheels in 964 NB fitment!
997 GT3 steel center exhaust muffler. $800
I was told this was taken off at 3k miles and replaced with a bypass. It certainly looks almost new. Tips are not included. Sharkwerks RS Light Weight Exhaust Tips 88mm tips are pictured ($350 new) that could be included for $250 extra. They are ceramic heat treated and 1+lb less then OEM tips.
I pulled these HDs from my 1993 962 C2. Last owner put these on and I've since installed Bilstein PSS10 (I wanted adjustability). These only have 5,000 miles on them and appear to be in excellent condition. On the fronts the housing for the brake line has been cut to allow you not to have to break the brake lines to install-this is a standard practice.
I took close up photos of the model numbers so you can check for fit.
New would cost approximately $900 plus tax. $600 plus shipping.
I have the original receipt - I think these carry a lifetime warranty.
I have a set of bottoms and backs in black leather for a 964 cabriolet. Excellent condition. Has the release pull **** at the base. $400 OBO
I have a set of backs in tan leather to fit a 964 or 993. Excellent condition. $250 OBO. Has the release button at the top. They fit my 964, but I can't recall trying them with the roof down. I think they would clear.
Flag mirrors off a 90 C2. Paint to sample "Sun Faded Red" with requisite stone chips. Mirror glass is perfect. $60 shipped to lower 48.
Pre-Black Friday price of $60 shipped to lower 48. Makes a great stocking stuffer. Or mini makeup mirror for your wife or girlfriend. Can't go any lower. Next stop is the range for target practice.
10-29-2015, 09:59 PM
