40-50 psi?
#16
Team Owner
Join Date: Oct 2009
Location: one thousand, five hundred miles north of Ft. Lauderdale for the summer.
Posts: 28,705
Received 212 Likes
on
153 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
http://www.aera.org/engine-professio...-head-gaskets/
btw, anyone ever run gasket sealer in between races?
or even leave it in there?
btw, anyone ever run gasket sealer in between races?
or even leave it in there?
#17
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Good article, thanks.
#18
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
There is another school of thought that perhaps having the stock intake manifold which produces a lot of early/mid range tq might increase the chance of the block flexing as opposed to your shorter runner style that might make it a little more progressive or linear and also occur a bit higher up in the rpms. Not sure on that.
One thing I'm curious about now and Harry may have an idea is what may happen when using an intake that flows say 20% more than the head. Isn't that going to cause some harmonic unbalance and alter ram effect in the whole intake tract?
I mean, if the differences in peak flow vary too greatly between the different sections of the inlet tract, isn't that going to alter head port velocity to a destructive extent?
#19
Drifting
Join Date: Aug 2009
Location: Bangkok, Thailand, Milpitas, CA & Weeki Wachee, FL
Posts: 2,239
Likes: 0
Received 2 Likes
on
1 Post
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I am doing quite a bit of research on the whole head stud main stud scenario right now. It is quite amazing on the differences in opinions I have received.
Patrick:
On your 9/16 setup, did they use Timeserts or Helicoils in the block for the studs? What torque recommendation did you receive for the head studs. I received a figure from Heritage that really threw me, 130 ft/lbs! What lubrication did they recommend for installation into the block and for the nuts. Feel free to PM me.
Patrick:
On your 9/16 setup, did they use Timeserts or Helicoils in the block for the studs? What torque recommendation did you receive for the head studs. I received a figure from Heritage that really threw me, 130 ft/lbs! What lubrication did they recommend for installation into the block and for the nuts. Feel free to PM me.
#20
Addict
Rennlist Member
Rennlist Member
Join Date: May 2001
Location: Parral, Chihuahua, Mejico
Posts: 929
Likes: 0
Received 5 Likes
on
5 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Porsche didn't design this engine to do a lot of pressure. If you stay below 20 psig they do fine.
At higher pressures, the cylinders shuffle, the head lifts and etc.
If you are going to do higher pressures, the block and head require major revisions.
At higher pressures, the cylinders shuffle, the head lifts and etc.
If you are going to do higher pressures, the block and head require major revisions.
#21
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
It's more like a Tractor engine and no use to try with stock block / head to go crazy. We will never achieve those crazy 40psi+ boost figures, well not if you want to drive home. Maybe Sid could pump things up a bit at the Drags but he'd need a cage. I think if we had a better intake we could run ours to say 30psi on the straights. Would be interesting.
#25
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Paully its best if you stay of youtube for a while..... Sadly you would have to pump lots and lots of money before you get anywhere sufficient.
#26
Team Owner
Join Date: Oct 2009
Location: one thousand, five hundred miles north of Ft. Lauderdale for the summer.
Posts: 28,705
Received 212 Likes
on
153 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
i didn't really post this, but if i really did post this, it'd say; good car w/ flawed powerplant, not horrible if not over-boosted, semi-exotic, petulant, expensive, pain in the *** to keep happy/maintain, engines sometimes worshipped by uber-purists/europeans/*****, w/ others often more fair and balanced, still over-boosted, wrenched and driven by astronauts, then, one day; BOOM, never boring, dissenters gtfo.
![Smilie](https://rennlist.com/forums/images/smilies/smile.gif)
#27
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
i didn't really post this, but if i really did post this, it'd say; good car w/ flawed powerplant, not horrible if not over-boosted, semi-exotic, petulant, expensive, pain in the *** to keep happy/maintain, engines sometimes worshipped by uber-purists/europeans/*****, w/ others often more fair and balanced, still over-boosted, wrenched and driven by astronauts, then, one day; BOOM, never boring, dissenters gtfo. ![Smilie](https://rennlist.com/forums/images/smilies/smile.gif)
![Smilie](https://rennlist.com/forums/images/smilies/smile.gif)
#28
Professional Hoon
Rennlist Member
Rennlist Member
Thread Starter
Join Date: Jan 2010
Location: Melbourne, Australia
Posts: 7,090
Likes: 0
Received 4 Likes
on
4 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Really? I'm sure someone would have?!
I know someone would try in melbourne. But finding him would be hand.
Oh i don't plan to!! if i wanted high boost, I would get an RB or a 2J
I know someone would try in melbourne. But finding him would be hand.
Oh i don't plan to!! if i wanted high boost, I would get an RB or a 2J
#29
Professional Hoon
Rennlist Member
Rennlist Member
Thread Starter
Join Date: Jan 2010
Location: Melbourne, Australia
Posts: 7,090
Likes: 0
Received 4 Likes
on
4 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Haven't got the gasket yet but here's the block and rings as of late last week. Gasket will be made of copper.
I was very hopeful that the deckplate and massive 9/16" headstuds clamped down much higher than stock would save me from doing something like this but no.
Not even at lowish 1.3bar boost. We were popping Cometic h/gaskets every race meeting. Not due to detonation either. So here we are now. Next......
I was very hopeful that the deckplate and massive 9/16" headstuds clamped down much higher than stock would save me from doing something like this but no.
Not even at lowish 1.3bar boost. We were popping Cometic h/gaskets every race meeting. Not due to detonation either. So here we are now. Next......
#30
Race Director