Group Buy: A.I.R 944 Front Splitter
#65
Addict
Lifetime Rennlist
Member
Lifetime Rennlist
Member
I'm not worried about fitment. It will fit fine. This is much traveled ground with A.I.R.
I just don't want one of you sketchy RL'ers sneaking onto my front steps to steal mine!
I just don't want one of you sketchy RL'ers sneaking onto my front steps to steal mine!
#67
Temprarily Banned per IB
I got mine, haven't even opened the box, the car is under 3' of snow. But it arrived a couple of days after the charge showed up on my account. But then again from what everyone else had already said about their integrity I had no doubt on the matter. Car is one huge project waiting to happen, when it does, I have some pics!
Regards,
Russell
Regards,
Russell
#69
Burning Brakes
Thread Starter
Join Date: Oct 2006
Location: San Diego (miramar), CA
Posts: 804
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 2bridges
damn ballastic - always two steps ahead of me -
#71
Burning Brakes
Thread Starter
Join Date: Oct 2006
Location: San Diego (miramar), CA
Posts: 804
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 2bridges
might have aced you for now with 968 hatch
supose you are going all red tailights too????
Damn good lookin car ballastic
supose you are going all red tailights too????
Damn good lookin car ballastic
I'm going a different route with my tail lights. When they are complete, i'll post pictures.
Your cars looking great also
#72
Burning Brakes
Thread Starter
Join Date: Oct 2006
Location: San Diego (miramar), CA
Posts: 804
Likes: 0
Received 0 Likes
on
0 Posts
Who else installed their splitter? The passangers side does not allign with the end of bumper. It's about 1/2'' inch off. I've tried tweaking it without much success...
This is the best comestic enhancement, PERIOD.
No picture of the bad side...
This is the best comestic enhancement, PERIOD.
No picture of the bad side...
Last edited by Ballistic-Chapman; 02-27-2007 at 04:30 AM.
#73
Addict
Lifetime Rennlist
Member
Lifetime Rennlist
Member
Virtually all 951 front noses are out of square. Any tiny little bump on the front bumper will bend them. If the car was ever hit in front you can bank on it being out of square. These splitters get made on a mold, and have been the same for years. It's best to take the nose off to install the splitter. Did you do it that way?
I'll be installing mine later tonight, but there is a huge chance it's your car rather than the part. In four years I've never heard a complaint about the part.
I'll be installing mine later tonight, but there is a huge chance it's your car rather than the part. In four years I've never heard a complaint about the part.
#74
Rennlist Member
Originally Posted by ehall
Virtually all 951 front noses are out of square. Any tiny little bump on the front bumper will bend them. If the car was ever hit in front you can bank on it being out of square. These splitters get made on a mold, and have been the same for years. It's best to take the nose off to install the splitter. Did you do it that way?
I'll be installing mine later tonight, but there is a huge chance it's your car rather than the part. In four years I've never heard a complaint about the part.
I'll be installing mine later tonight, but there is a huge chance it's your car rather than the part. In four years I've never heard a complaint about the part.
#75
Addict
Lifetime Rennlist
Member
Lifetime Rennlist
Member
I wouldn't go that far, but you can make it a lot better. It depends on how far out your nose is. Every car is different. The splitter, just as the batwing, gives lower reinforcement for the proper shape of the nose. By removing the nose, you are better able to manipulate the shape of the nose to fir the splitter properly. Remember, the splitter hasn't been hit. It's the proper size. The nose...not so much.