How NOT to do it: destroyed intake manifold while attaching fuel rail
#1
How NOT to do it: destroyed intake manifold while attaching fuel rail
Anyone else ever done that?
I thought I was nearing the end of my big winter project... I have repaired a leak in the exhaust crossover pipe, installed a new camshaft housing gasket, replaced all the front seals and did the timing and balance belts and water pump gasket.
This morning, as I was attaching the fuel rail, I ran into a snag.
The injectors didn't want to "pop" into place on the intake manifold. But I figured as I torqued down the bolts that mount the fuel rail onto the intake manifold, they would. (I should have taken them out and lubed them, so this was mostly my fault)
I was applying a fair amount of torque, but then the intake manifold cracked, just as the fuel rail bracket was seating against the intake manifold. It seems that the bolt was too long for the hole. The tip of the bolt seated inside the hole *before* or *as* the bracket seated outside the hole. If I'd added another washer, I'd have been fine. But instead, the manifold cracked.
So, I guess I'm in the market for an intake manifold.
I thought I was nearing the end of my big winter project... I have repaired a leak in the exhaust crossover pipe, installed a new camshaft housing gasket, replaced all the front seals and did the timing and balance belts and water pump gasket.
This morning, as I was attaching the fuel rail, I ran into a snag.
The injectors didn't want to "pop" into place on the intake manifold. But I figured as I torqued down the bolts that mount the fuel rail onto the intake manifold, they would. (I should have taken them out and lubed them, so this was mostly my fault)
I was applying a fair amount of torque, but then the intake manifold cracked, just as the fuel rail bracket was seating against the intake manifold. It seems that the bolt was too long for the hole. The tip of the bolt seated inside the hole *before* or *as* the bracket seated outside the hole. If I'd added another washer, I'd have been fine. But instead, the manifold cracked.
So, I guess I'm in the market for an intake manifold.
#2
RL Community Team
Rennlist Member
Rennlist Member
That sucks, dude!
I'm sure you could get away with only 3 of 4 bolts holding down the fuel rail. But if you have time, it would be best to replace the intake manifold. Where are you located? I have a spare NA intake if you can't find one locally.
I'm sure you could get away with only 3 of 4 bolts holding down the fuel rail. But if you have time, it would be best to replace the intake manifold. Where are you located? I have a spare NA intake if you can't find one locally.
#3
Fuel rail/injector install tools.
#4
If I drilled out a few more mm and tapped it and used a slightly longer bolt, then the broken piece would be essentially acting as a spacer in compression (and shouldn't move with or without jbweld).
I gotta think about that...
#5
Anyone who has one they could ship (or for pickup here, Richmond, or NoVA), I'd love to hear from!
#6
#7
Dunno about that, I can say that I've done hundreds of them with the above two things though. Never had one break. You do have to have some sort of self control though, beating the snot out of them might be fun, but kinda defeats the purpose.
Trending Topics
#8
Mine cracked in some place near the rear intake-side bracket. The intake has been off before to change the turbo and that's all I know. From what I could tell it cracked "Just because." I've seen a few threads on here about cracked rails and people patching them by getting them brazed as well.
#9
Administrator - "Tyson"
Lifetime Rennlist
Member
Lifetime Rennlist
Member
#13
You can get away with a lot of bolts on any car, one that keeps the fuel injectors from spraying down your hot engine with gasoline is not one of them.
#14
Rennlist Member
Manifold
I have a perfect condition manifold. My care came with the Lindsey Racing intake manifold as well as the factory unit.
I will send you a PM
I will send you a PM
#15
RL Community Team
Rennlist Member
Rennlist Member
On the NA, these little bolts don't really hold the fuel rail from jumping off and allowing fuel to gush all over, they just hold the fuel rail from vibrating around. On the turbo, especially if you're running higher boost, I'd make sure all the bolts are fastened properly. I wouldn't trust JB weld or anything like that.