Frenzy 18 (2014) for sale/swap thread.
#16
Drifting
These are the ABS door cards were speaking of, any experience with those?
Ill bring that fan controler for you so be sure to introduce yourself to me at Frenzy.
Mj
#17
Addict
Rennlist Member
Rennlist
Site Sponsor
Rennlist Member
Rennlist
Site Sponsor
Nothing hard in trimming them. But it takes time and attention to detail.
You'll want to drill the holes with metric drill bits.
Rather than hijack this thread, there is more discussion here on these door panels.
You'll want to drill the holes with metric drill bits.
Rather than hijack this thread, there is more discussion here on these door panels.
#18
Rennlist Member
I'll have a bunch of stuff there too... clear lenses, fire extinguisher brackets and more.
Also, I might dig into the goodie bin and bring some choice items I'd been holding on to.
Also, I might dig into the goodie bin and bring some choice items I'd been holding on to.
#19
Three Wheelin'
I can bring the following :
'88 VDO instument cluster manual transmission (new gear 133,000 miles) : $350
'88 fuse block electrical panel 928.610.105.16 : $275
'88 Rear Center Console Storage Box - Non-air Blue : $300
'88 Front Subframe Crossmember : $125
I also have a 1987-1991 Rear Bumper Cover but I don't think it will fit in the trunk ....
All price OBO.
'88 VDO instument cluster manual transmission (new gear 133,000 miles) : $350
'88 fuse block electrical panel 928.610.105.16 : $275
'88 Rear Center Console Storage Box - Non-air Blue : $300
'88 Front Subframe Crossmember : $125
I also have a 1987-1991 Rear Bumper Cover but I don't think it will fit in the trunk ....
All price OBO.
Last edited by oups59; 09-14-2014 at 08:18 AM.
#20
Race Car
I have a pair of Cup II fronts, ET55, Porsche. Could use refinishing, haven't run them yet, purportedly one has slight bend that balances out. Been saying $100 picked up. For the pair.
Also have old 944/964 offset Milles if anyone has other interests.
Used tensioner 70K, $20.
Have a NIB factory "U" fuel hose...pure unobtanium...but I think I'm keeping it. ;-)
Have to check on whether I sold my RMB..
Will have to rummage around for other stuff.
Also have old 944/964 offset Milles if anyone has other interests.
Used tensioner 70K, $20.
Have a NIB factory "U" fuel hose...pure unobtanium...but I think I'm keeping it. ;-)
Have to check on whether I sold my RMB..
Will have to rummage around for other stuff.
#21
Team Owner
I am looking for the mirror switch L/R U/D and the console it sits in,
as well as the left/ right rocker switch,
anyone have an extra sitting around?
as well as the left/ right rocker switch,
anyone have an extra sitting around?
#22
Drifting
#23
Rennlist Member
I'm looking for a used horn - the longer of the two. Anybody have one laying around? I'll bring my old one and we can disect it and try to figure out why it went bad. I have opened it up and for the life of me, cannot figure out why it failed.
#24
Team Owner
Ed if the wire leads have continuity then it may be as simple as an adjustment of the limit screw on the coil,
this is done with the horn assembled .
NOTE if there isnt any continuity, open the horn and check the wire for broken solder joints.
simply unscrew the bolt till the horn starts to work, or try screwing it inwards.
this is done with 12V applied to the leads.
this is done with the horn assembled .
NOTE if there isnt any continuity, open the horn and check the wire for broken solder joints.
simply unscrew the bolt till the horn starts to work, or try screwing it inwards.
this is done with 12V applied to the leads.
#25
Rennlist Member
#26
Rennlist Member
Ed if the wire leads have continuity then it may be as simple as an adjustment of the limit screw on the coil,
this is done with the horn assembled .
NOTE if there isnt any continuity, open the horn and check the wire for broken solder joints.
simply unscrew the bolt till the horn starts to work, or try screwing it inwards.
this is done with 12V applied to the leads.
this is done with the horn assembled .
NOTE if there isnt any continuity, open the horn and check the wire for broken solder joints.
simply unscrew the bolt till the horn starts to work, or try screwing it inwards.
this is done with 12V applied to the leads.
#28
Rennlist Member
I have a 'concours' condition rear GT/GTS muffler that I could bring - $200 or acceptable offer. If anyone wants it, please send me a PM or e-mail so I can get it out and bring it. Pix available (stainless - perfect, actually look brand new, I took it in a trade for something). if you want pix - again, send a message with your e-mail address.
I'll also be bringing a pair of the most beautiful door inserts (replacement for the leather inserts above the armrest) I've ever seen. These were custom made from a very rare Hawaiian wood - Koa, and simply replace the 'dull'(!!) leather pieces Porsche provided. Everyone who saw them in my S4's thought they really beautified the interior. $250 or acceptable offer. Pictures below:
I'll also be bringing a pair of the most beautiful door inserts (replacement for the leather inserts above the armrest) I've ever seen. These were custom made from a very rare Hawaiian wood - Koa, and simply replace the 'dull'(!!) leather pieces Porsche provided. Everyone who saw them in my S4's thought they really beautified the interior. $250 or acceptable offer. Pictures below:
Last edited by Gary Knox; 09-16-2014 at 04:26 PM.
#29
#30
Rennlist Member
BeerFish is always on the market for sale! Needs to go to someone who knows what a 84-85 EURO 5-speed with lots of killer mods is. Or if you just want to own one of the fastest non-boost (still faster than many of those) sharks out there. AND she looks pretty cool too in my opinion.