Rennlist - Porsche Discussion Forums - Search Results

Notices
 
Search: Posts Made By: outbackgeorgia
Showing results 1 to 25 of 492
Search took 0.49 seconds.
Forum: 928 Forum
08-15-2018, 12:49 AM
Replies: 19
Views: 801
Posted By outbackgeorgia

When I lived in Florida, it was a "no fault"...

When I lived in Florida, it was a "no fault" state. Has this changed?
You would be dealing with your own insurance company.
Dave
Forum: 928 Forum
07-12-2018, 02:38 PM
Replies: 11
Views: 362
Posted By outbackgeorgia

You are looking at the pressure relief valve off...

You are looking at the pressure relief valve off the receiver dryer, not the low port. Leave it alone! The low port is under the upper rad hose on pass. side.
Forum: 928 Forum
05-04-2018, 03:07 AM
Replies: 14
Views: 433
Posted By outbackgeorgia

Puzzeling, as it is a dual master cylinder. Both...

Puzzeling, as it is a dual master cylinder. Both should not fail at the same time. Dual tandem master brake cylinders have been mandated for years. If one fails, should still stop, indicator light...
Forum: 928 Forum
05-04-2018, 02:24 AM
Replies: 14
Views: 433
Posted By outbackgeorgia

Ron, What Greg said. 1. M/Cyl is shot....

Ron,
What Greg said.
1. M/Cyl is shot. replace it. I know it is painful.$$$
Do not understand why a rebuild kit is not available. Back in the day we just replaced rubber bits.
2. Dual plate...
Forum: 928 Forum
05-02-2018, 12:36 AM
Replies: 501
Views: 52,418
Posted By outbackgeorgia

That will be a great time I will be missing, as I...

That will be a great time I will be missing, as I will be in FL for a special "family" wedding event. I am really sorry to have to miss this special event! Best to all,
Dave
Forum: 928 Forum
04-27-2018, 12:02 AM
Replies: 15
Views: 587
Posted By outbackgeorgia

Ron, Even after the problem is fixed, switches,...

Ron,
Even after the problem is fixed, switches, lines, bleeding, etc. the lights will continue to flash until it is reset by disconnecting the battery for a few minutes. This drove me crazy on my...
Forum: 928 Forum
03-31-2018, 10:02 PM
Replies: 322
Views: 37,880
Posted By outbackgeorgia

Jerry, fantastic project and thread. Following...

Jerry, fantastic project and thread. Following closely, you have vision!
Dave
Forum: 928 Forum
03-29-2018, 12:35 AM
Replies: 322
Views: 37,880
Posted By outbackgeorgia

Jerry, Sunday afternoon welding rod, don't...

Jerry,
Sunday afternoon welding rod, don't laugh, metal coat hangars! Have saved many a project using them. Surprising quality mild steel, exhausts, sheet metal, etc. Not something for structural...
Forum: 928 Forum
02-27-2018, 09:43 PM
Replies: 501
Views: 52,418
Posted By outbackgeorgia

Hi Brian, sorry I missed you at Rich's shop. Hope...

Hi Brian, sorry I missed you at Rich's shop. Hope to see ypu soon at a gathering, Dave
Forum: 928 Forum
12-28-2017, 09:08 AM
Replies: 17
Views: 1,171
Posted By outbackgeorgia

Looks loke a fatigue break, notice the failure at...

Looks loke a fatigue break, notice the failure at the end of the crimp. Possibly the wire was not secured properly and constant flexing over the years caused separation. Replace the wire and secure...
Forum: 928 Forum
11-27-2017, 10:53 PM
Replies: 13
Views: 597
Posted By outbackgeorgia

OK, makes sense, but the slope is steep and...

OK, makes sense, but the slope is steep and slippery! There are a lot of old parts in that engine!
Forum: 928 Forum
11-27-2017, 10:31 PM
Replies: 13
Views: 597
Posted By outbackgeorgia

Sooooooo, you want ti fix something that is not...

Sooooooo, you want ti fix something that is not broken?
Forum: 928 Forum
09-12-2017, 01:09 AM
Replies: 10
Views: 1,030
Posted By outbackgeorgia

Notice they monitored fuel pressure.

Notice they monitored fuel pressure.
Forum: 928 Forum
08-23-2017, 11:58 PM
Replies: 20
Views: 1,439
Posted By outbackgeorgia

Pull the pod? $100? Wow, prices have gone up. I...

Pull the pod? $100? Wow, prices have gone up. I don't recall pulling the pod for the switch, just two tiny screws
Forum: 928 Forum
08-05-2017, 01:04 AM
Replies: 45
Views: 1,685
Posted By outbackgeorgia

All of the evidence points to a thread pitch...

All of the evidence points to a thread pitch mismatch. The nuts should thread enough to veryify. They are locknuts, correct? There are metric thread pitches that are very close, but mismatched. I...
Forum: 928 Forum
07-20-2017, 08:53 PM
Replies: 302
Views: 43,368
Posted By outbackgeorgia

This is a forum, share. PM's are for private...

This is a forum, share. PM's are for private messages, realy a strange request.
Forum: 928 Forum
07-20-2017, 08:51 PM
Replies: 81
Views: 5,620
Posted By outbackgeorgia

Congratulations, love the color, a great find,...

Congratulations, love the color, a great find, close enough to an S4 to be a great car. I do have a slightly different vision, first replace ALL the fuel lines if they are not new. Maybe a little...
Forum: 928 Forum
06-28-2017, 03:08 AM
Replies: 14
Views: 615
Posted By outbackgeorgia

IS

IS
Forum: 928 Forum
06-24-2017, 09:58 AM
Replies: 21
Views: 1,551
Posted By outbackgeorgia

What Sean said

What Sean said
Forum: 928 Forum
06-23-2017, 03:21 PM
Replies: 21
Views: 1,551
Posted By outbackgeorgia

Just do it. The LH will fail. There is a hybrid...

Just do it. The LH will fail. There is a hybrid chip inside that fails due to age. Its now or later, you may be on the road somewhere when it fails.
Forum: 928 Forum
06-16-2017, 08:49 PM
Replies: 21
Views: 1,281
Posted By outbackgeorgia

I don't disagree, but what works for me may not...

I don't disagree, but what works for me may not be the best solution for everyone. If I Needed a new sensor, I would still solder it in to eliminate the connector. Part of that process is to assure...
Forum: 928 Forum
06-16-2017, 08:26 PM
Replies: 11
Views: 1,936
Posted By outbackgeorgia

Bonding the stud in has no effect on the safety...

Bonding the stud in has no effect on the safety or integrity of the steering system. It just holds the stud while tightening the nut.I would not deface the stud in any manner.
Dave
Forum: 928 Forum
06-16-2017, 01:23 AM
Replies: 21
Views: 1,281
Posted By outbackgeorgia

The sensor itself probably has not failed, just...

The sensor itself probably has not failed, just the connector. There are no active parts in the sensor, just a coil of wire. Quick fix/test, skip the connector, solder the wires, shrink wrap....
Forum: 928 Forum
06-13-2017, 12:16 AM
Replies: 64
Views: 7,264
Posted By outbackgeorgia

Just print out the PET, have all the diagrams...

Just print out the PET, have all the diagrams ready when needed!
Forum: 928 Forum
06-11-2017, 11:59 PM
Replies: 105
Views: 6,733
Posted By outbackgeorgia

16" phone dials, nice!

16" phone dials, nice!
Showing results 1 to 25 of 492
 


 
Forum Jump

Contact Us - About Us - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.