Rennlist - Porsche Discussion Forums - Search Results

Notices
Search: Posts Made By: Derboost
Showing results 1 to 15 of 15
Search took 0.32 seconds.
Forum: 996 Forum
07-14-2012, 12:14 PM
Replies: 8
Views: 6,264
Posted By Derboost

thanks, just replaced my master cyl and getting...

thanks, just replaced my master cyl and getting psm abs lights:banghead:, have you ever heard of a way to activate the pump by direct wire?
hopefully durametric will work, I just don't want to...
Forum: 996 Forum
07-14-2012, 11:54 AM
Replies: 8
Views: 6,264
Posted By Derboost

Did you ever get a answer for the correct...

Did you ever get a answer for the correct sequence?
04-19-2008, 02:40 PM
Replies: 47
Views: 2,427
Posted By Derboost

Also depends on the laws in your state, Arizona...

Also depends on the laws in your state, Arizona no DV at all period. I was in my e36 M3 LW stopped for a train, hit in the rear,lady on cell phone doing 45. 9500.00 damage No DV. I sued, 2 years. Got...
02-06-2008, 09:22 PM
Replies: 8
Views: 375
Posted By Derboost

Very, very, easy, just a bit of stuff to unbolt,...

Very, very, easy, just a bit of stuff to unbolt, do it all at home and then go to the dyno....
remove lower plastic, then unbolt shaft from trans, (4 bolts) wiggle about and slide out of front...
02-03-2008, 11:08 PM
Replies: 35
Views: 1,786
Posted By Derboost

Yup, same here, bullitproof motor, just a really...

Yup, same here, bullitproof motor, just a really nice car.
02-02-2008, 11:03 PM
Replies: 19
Views: 1,715
Posted By Derboost

[QUOTE=tkerrmd;5059614] they say they cant talk...

[QUOTE=tkerrmd;5059614] they say they cant talk to me, QUOTE]


LOL, thats a bonus !!!!......:icon501:
01-30-2008, 10:52 AM
Replies: 19
Views: 1,715
Posted By Derboost

Fabspeed and FVD both make a nice pipe to do...

Fabspeed and FVD both make a nice pipe to do this, it's really LOUD and drones bigtime in the car, at WOT it sounds great, every place else it is not so good... you might try the "hole" mod to the...
01-21-2008, 02:05 PM
Replies: 13
Views: 486
Posted By Derboost

mine had a little "block-clip" in the gear rack...

mine had a little "block-clip" in the gear rack blocking the pinion gear, I took this out and got maybe another inch.
01-21-2008, 11:23 AM
Replies: 0
Views: 13,834
Posted By Derboost

Front wheel bearing replacement 996tt,C4,GT2

Now let me say that this job was quite straightfoward, BUT I would suggest that you have a bit of experience
in bearing fittting as well as presswork or you may really mess things up in a big way....
Forum: 996 Forum
01-20-2008, 08:58 PM
Replies: 15
Views: 2,160
Posted By Derboost

thanks, I was going to do one on the rears but I...

thanks, I was going to do one on the rears but I was getting a wee bit upset at that point and forgot to take any pics, I was in "race deadline" mode as my loving wife puts it...... Now its been...
Forum: 996 Forum
01-20-2008, 06:12 PM
Replies: 15
Views: 2,160
Posted By Derboost

correct, large nut with very special torque...

correct, large nut with very special torque limiting gun, they are pretty cool...and $$$$$$$$
Forum: 996 Forum
01-20-2008, 06:10 PM
Replies: 15
Views: 2,160
Posted By Derboost

I owned my own shop, we did Busch,Woo,northwest...

I owned my own shop, we did Busch,Woo,northwest tour,winston west, southwest tour,outlaw late models,superstock,comp eliminator, and a whole lot of Blown alcohol drag stuff.
now i'm justa cranky...
Forum: 996 Forum
01-20-2008, 01:56 PM
Replies: 15
Views: 2,160
Posted By Derboost

Sorry, i've been a race engine builder all my...

Sorry, i've been a race engine builder all my life, impacts are not for me.Air tools have there place but not to remove a splined shaft or near cv joints, IMHO


Yes it is a little cold up here,...
Forum: 996 Forum
01-20-2008, 08:59 AM
Replies: 15
Views: 2,160
Posted By Derboost

thank you, I did my rears also,:banghead: boy...

thank you, I did my rears also,:banghead: boy were they shot........
Forum: 996 Forum
01-19-2008, 10:44 PM
Replies: 15
Views: 2,160
Posted By Derboost

DIY front wheel bearing replacement 996 tt,c4,GT2

Now let me say that this job was quite straightfoward, BUT I would suggest that you have a bit of experience
in bearing fittting as well as presswork or you may really mess things up in a big way....
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - About Us - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.