Rennlist - Porsche Discussion Forums - Search Results

Notices
 
Search: Posts Made By: dutchcrunch
Showing results 1 to 25 of 471
Search took 0.77 seconds.
Yesterday, 03:44 AM
Replies: 4
Views: 3,100
Posted By dutchcrunch

That car is sold. I inquired back in February

That car is sold. I inquired back in February
Forum: 964 Forum
04-28-2019, 07:49 PM
Replies: 7
Views: 631
Posted By dutchcrunch

Intermediate shaft bearing I would replace with...

Intermediate shaft bearing I would replace with Porsche , cheap. Those wear kinda fast.The nose bearing seal I would source from a a quality Viton set like from Steve Weiner. What kind of mileage...
Forum: 964 Forum
04-28-2019, 02:06 PM
Replies: 7
Views: 631
Posted By dutchcrunch

Oem bearing

I can confirm that the bearing that are sourced directly from Porsche have signs of being measured in-house . The rod bearings for sure. I think the rod bearing are the ones with issues. The rod...
02-11-2019, 12:08 PM
Replies: 7
Views: 3,511
Posted By dutchcrunch

car sale

Hello Owen, I emailed to you earlier , perhaps we can have a brief 10 minute phone chat about your car, let me know if that's possible.


Frank
02-05-2019, 08:09 PM
Replies: 4
Views: 3,100
Posted By dutchcrunch

I texted you. Hope the listed number is correct

I texted you. Hope the listed number is correct
Forum: 964 Forum
07-04-2018, 04:15 PM
Replies: 122
Views: 15,663
Posted By dutchcrunch

pocket repair

i'll take a set 964 shoulder version
01-12-2018, 10:35 AM
Replies: 5
Views: 2,591
Posted By dutchcrunch

1990 964 c2 for sale

1990 c2 coupes with sunroof . black on black factory sport seats .lsd. motor resealed with updated cylinders. Motor completely resealed. Parts soured from porsche. Car runs and drives great....
Forum: 964 Forum
11-29-2017, 12:54 PM
Replies: 3
Views: 427
Posted By dutchcrunch

rockers

even if new , check for square, new ones known not to be..............
Forum: 964 Forum
10-04-2017, 02:51 PM
Replies: 14
Views: 874
Posted By dutchcrunch

tensioner

the factory tensioner are not a solid tensioner, there is a calibrated spring with a set dimension you dial in to a mark..... this is to simulate how the engine will run with tensioners in place. ...
Forum: 964 Forum
10-04-2017, 02:45 PM
Replies: 14
Views: 874
Posted By dutchcrunch

timing

1.26 is at overlap. on another note, unless you set the the z1 mark on the pulley to true top dead center of the crank your gonna be off. stomki should have told you that. on the pulley...
Forum: 964 Forum
09-16-2017, 03:02 PM
Replies: 1
Views: 376
Posted By dutchcrunch

alternator shims

are the shims available from Porsche runner a smaller od than the originals, does anyone know
Forum: 964 Forum
09-06-2017, 09:26 PM
Replies: 23
Views: 2,931
Posted By dutchcrunch

back side

do it at the adjuster, regular way, you don't have to worry about this.
Forum: 964 Forum
09-06-2017, 09:24 PM
Replies: 23
Views: 2,931
Posted By dutchcrunch

backside method

if you do the backside method make sure you see if there is a tighter side on the rocker pad to cam and use this area as the rockers are known not to be square to the cam. do it adjuster , you...
Forum: 964 Forum
08-07-2017, 07:08 PM
Replies: 21
Views: 1,618
Posted By dutchcrunch

Smile rms

John McM, that real nice, and the info will be real handy to anyone questioning this topic. Nice job John
Forum: 964 Forum
08-06-2017, 11:15 AM
Replies: 21
Views: 1,618
Posted By dutchcrunch

rms

using that Porsche seal with the reduced outer sealing ring is risky if its not correct. I have used it before with success ,but the elring seal is the way to go.
Forum: 964 Forum
08-05-2017, 11:55 PM
Replies: 21
Views: 1,618
Posted By dutchcrunch

rms

hey John McM , look at this and look at john walkers workshop reply, here is the link
...
Forum: 964 Forum
08-05-2017, 11:50 PM
Replies: 21
Views: 1,618
Posted By dutchcrunch

rms

c4inla, yours is the Porsche factory seal and looks good.


john mcm, your seal is the elring type and looks to be installed all the way in. I would not say that its wrong just set all the way...
Forum: 964 Forum
08-05-2017, 07:07 PM
Replies: 21
Views: 1,618
Posted By dutchcrunch

rms

(SW)
Forum: 964 Forum
08-05-2017, 07:06 PM
Replies: 21
Views: 1,618
Posted By dutchcrunch

rms leak

if you used the porsche seal that has about half of the outer seal reduced, that's your problem. that seal need to be at least flush. I would drop the engine, its a bear but safer as not to put...
Forum: 964 Forum
06-22-2017, 10:01 PM
Replies: 12
Views: 1,522
Posted By dutchcrunch

sealant

the thing with 574 that's nice is the squeeze out like around the valve springs that is present in the previous picture is solid and has a tenacious grip when it dries and is less likely to come...
06-21-2017, 12:57 PM
Replies: 30
Views: 3,885
Posted By dutchcrunch

A car

Check your rennlist mail
06-21-2017, 12:56 PM
Replies: 30
Views: 3,885
Posted By dutchcrunch

Hello

Check your rennlist mail
Forum: 964 Forum
05-09-2017, 02:22 PM
Replies: 4
Views: 485
Posted By dutchcrunch

webcam regrinds

has anyone used webcam regrinds and have any issues????? Thanks
Forum: 964 Forum
05-05-2017, 04:54 AM
Replies: 54
Views: 11,535
Posted By dutchcrunch

nose bearing oring

im in the process of rebuilding my engine and have already closed the case.

but I can tell you that from the factory build when I took the motor apart, you could see the marks as posted in your...
Forum: 964 Forum
08-04-2015, 09:13 PM
Replies: 19
Views: 1,976
Posted By dutchcrunch

ppi

so what does a ppi cost these days ?
Showing results 1 to 25 of 471
 


 
Forum Jump

Contact Us - About Us - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.