Rennlist - Porsche Discussion Forums - Search Results

Notices
 
Search: Posts Made By: Eric_Oz_S2
Showing results 1 to 25 of 495
Search took 0.59 seconds.
03-24-2019, 01:21 AM
Replies: 16
Views: 1,248
Posted By Eric_Oz_S2

Thanks - I noticed that on my S2 (window stays...

Thanks - I noticed that on my S2 (window stays powered). I have always had to keep my battery connected to a trickle charger due to drain. Can you successfully restore these switches through...
01-21-2018, 07:41 AM
Replies: 11
Views: 1,492
Posted By Eric_Oz_S2

It will be one or both pin receiving...

It will be one or both pin receiving housing/latches out of alignment. Just adjust them so pin is centred.
12-24-2017, 02:08 AM
Replies: 30
Views: 1,844
Posted By Eric_Oz_S2

Given that the fault happened when you...

Given that the fault happened when you reinstalled the pump, it seems to be either a faulty pump or a problem with the electrical connection at the pump. Have you measured voltage through the...
12-18-2017, 07:11 AM
Replies: 273
Views: 44,822
Posted By Eric_Oz_S2

Wheel rate is spring rate x motion ratio squared...

Wheel rate is spring rate x motion ratio squared x spring inclination factor. You haven't squared the motion ratio, hence previous poster was correct in saying your wheel rate calculation is wrong.
12-07-2017, 05:41 AM
Replies: 15
Views: 3,530
Posted By Eric_Oz_S2

That's the M150 leaded gas (no o2 sensor) plug...

That's the M150 leaded gas (no o2 sensor) plug bridging white and brown. That's not the japan model plug which bridges the other 2 wires in that 3 pin plug.
The black plug is a characteristic...
12-06-2017, 06:59 AM
Replies: 9
Views: 1,027
Posted By Eric_Oz_S2

Sounds about right. Expect around 150 engine...

Sounds about right. Expect around 150 engine cold, and around 170 engine hot. Don't worry about oil, just test with engine hot. You should be more concerned about differences between cylinders. ...
11-28-2017, 08:56 AM
Replies: 262
Views: 21,015
Posted By Eric_Oz_S2

Eaton is not very thermally efficient (high...

Eaton is not very thermally efficient (high temp), prone to heat soak and does not have a good top end. Ok for a street cruiser, bad for track use. Not really in keeping with the character of a...
11-27-2017, 05:23 AM
Replies: 262
Views: 21,015
Posted By Eric_Oz_S2

I've been running a Rotrex supercharger on my S2...

I've been running a Rotrex supercharger on my S2 for 5 years now. I have been running it hard on the track for all of this time. You can find details in my thread. It's not hard, but takes a lot of...
11-18-2017, 06:08 AM
Replies: 22
Views: 26,544
Posted By Eric_Oz_S2

So true about the tensioner bolts. Just stripped...

So true about the tensioner bolts. Just stripped the thread in the head. Good advice about using a longer bolt. The stock length is 15mm thread. I cut a 25mm thread bolt down to 22mm and this fixed...
08-18-2017, 09:44 PM
Replies: 20
Views: 4,664
Posted By Eric_Oz_S2

Reporting back experience on a different track. ...

Reporting back experience on a different track. The nittos are much better behaved on this surfacing. They still kick out at the rear a little but they snap back to traction under throttle quite...
07-25-2017, 08:23 AM
Replies: 20
Views: 4,664
Posted By Eric_Oz_S2

Thanks all for your responses. To answer a few...

Thanks all for your responses. To answer a few questions, the production date is late 2015 so not that old really. Suspension setup is as follows

Porsche 944s2 supercharged

350f springs, Kong...
07-24-2017, 08:16 AM
Replies: 20
Views: 4,664
Posted By Eric_Oz_S2

Nitto NT01 tyre/tire query

I have just returned from a weekend sprint and have to say I have never felt my car be so unpredictable on the limit before.

I have previously run a range of tyres types including Hoosier R6,...
07-12-2017, 07:20 AM
Replies: 6
Views: 932
Posted By Eric_Oz_S2

No, I am suggesting there is too much lateral...

No, I am suggesting there is too much lateral movement of the valve stem due to worn guides. The seals could just be worn out, so pretty easy to just replace them and see if that fixes the problem,...
07-11-2017, 06:42 AM
Replies: 6
Views: 932
Posted By Eric_Oz_S2

No trick. They shouldn't move. Perhaps your...

No trick. They shouldn't move. Perhaps your valve guides are worn? Pretty common on turbos to have excessive guide wear.
Forum: 968 Forum
06-23-2017, 08:02 PM
Replies: 626
Views: 106,726
Posted By Eric_Oz_S2

Thanks for the updates. Photos are great and car...

Thanks for the updates. Photos are great and car is looking good.
08-31-2016, 09:12 AM
Replies: 36
Views: 7,587
Posted By Eric_Oz_S2

I found the hankooks heat cycled out faster than...

I found the hankooks heat cycled out faster than the R6.
Forum: 968 Forum
08-30-2016, 07:22 AM
Replies: 8
Views: 693
Posted By Eric_Oz_S2

I would replace it with a resonator pipe, like a...

I would replace it with a resonator pipe, like a magnaflow.

You will likely gain power up top where it matters for a track car.
Forum: 968 Forum
08-28-2016, 08:13 AM
Replies: 626
Views: 106,726
Posted By Eric_Oz_S2

I hope the weekend went well for you. Looks like...

I hope the weekend went well for you. Looks like good weather.

I hope you can post some photos of the weekend.
08-26-2016, 05:44 AM
Replies: 3
Views: 728
Posted By Eric_Oz_S2

Michael Does that include alusil compatible...

Michael
Does that include alusil compatible Pistons?
08-22-2016, 07:53 AM
Replies: 3
Views: 434
Posted By Eric_Oz_S2

There's a calibration adjuster on the tacho? ...

There's a calibration adjuster on the tacho? Wish I knew that when I had mine out last.
Forum: 968 Forum
07-29-2016, 10:05 AM
Replies: 626
Views: 106,726
Posted By Eric_Oz_S2

Great reading your thread. Looks like you have...

Great reading your thread. Looks like you have put a lot of work into the car.
Forum: 964 Forum
04-04-2016, 07:54 AM
Replies: 22
Views: 2,347
Posted By Eric_Oz_S2

Knock sensor failures are not uncommon. I'm not...

Knock sensor failures are not uncommon. I'm not sure if your setup detects a faulty sensor as knock. Normally the dme will detect a faulty sensor (due to improbable inputs) and retard ignition. I...
Forum: 964 Forum
04-02-2016, 10:22 PM
Replies: 22
Views: 2,347
Posted By Eric_Oz_S2

Possible causes for high knock Faulty...

Possible causes for high knock

Faulty injector or injector lead (check for kinked cables, missing insulation, etc)
Faulty hall sensor will retard ignition and shouldn't affect knock (but will...
03-19-2016, 09:25 PM
Replies: 22
Views: 1,111
Posted By Eric_Oz_S2

I saw one comment on social media: "Lewis...

I saw one comment on social media:

"Lewis could have waved his own chequered flag at the end of Q3".

Sums it up really.
02-05-2016, 05:24 AM
Replies: 7
Views: 1,375
Posted By Eric_Oz_S2

Pauly Nice write up. As a point of...

Pauly

Nice write up.

As a point of reference I'll tell you about my experience. I rebuilt my torque tube probably 5 or 6 years ago. I used acetate plastic sleeves to the spec in Clarks...
Showing results 1 to 25 of 495
 


 
Forum Jump

Contact Us - About Us - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.