Rennlist - Porsche Discussion Forums - Search Results

Notices
 
Search: Posts Made By: odonnell
Showing results 1 to 25 of 493
Search took 0.41 seconds.
03-19-2019, 09:55 PM
Replies: 11
Views: 476
Posted By odonnell

You may as well order the parts now for the other...

You may as well order the parts now for the other side.

Genuine joints aren't that expensive. It just requires the time investment of taking the axle apart and swapping them.
03-14-2019, 08:52 PM
Replies: 17
Views: 1,249
Posted By odonnell

My idea for using the FIDLE output was this,...

My idea for using the FIDLE output was this, curious to hear your opinion:

- Middle pin gets 12v
- One outer pin gets chassis ground, however, there is a resistor in series.
- Other outer pin...
03-09-2019, 01:40 PM
Replies: 7
Views: 337
Posted By odonnell

If you have early shafts, the Vanagon/Syncro...

If you have early shafts, the Vanagon/Syncro joints are a direct swap. The shafts themselves should always be good to go. I was able to find genuine GKN-Loebro joints for around $40 each from a Bus...
03-05-2019, 10:32 PM
Replies: 17
Views: 1,249
Posted By odonnell

Man, I am so excited to see a skilled/competent...

Man, I am so excited to see a skilled/competent enthusiast developing in this area. Great work!
03-05-2019, 09:30 AM
Replies: 29
Views: 983
Posted By odonnell

Interesting project. One note though, you still...

Interesting project. One note though, you still need to retain almost all of the factory EFI hardware to retain spark control. However since the 944S has a factory 60-2 trigger wheel, you can cheaply...
03-04-2019, 11:40 PM
Replies: 26
Views: 2,583
Posted By odonnell

Almost all of the jumper wires are hooked up to...

Almost all of the jumper wires are hooked up to their assigned pins. I'll be doing some wire management to keep them organized. My next task is connecting the wires that require a splitter (some pins...
03-02-2019, 08:54 AM
Replies: 415
Views: 45,677
Posted By odonnell

In short, yes. The best practice is to set the...

In short, yes. The best practice is to set the ignition timing to a fixed level, say 10 or 15 deg BTDC. Then clamp around the #1 plug wire and check your timing. Should match your fixed value. If...
03-01-2019, 08:31 PM
Replies: 28
Views: 1,773
Posted By odonnell

For an NA 944 it's not a big deal. It's just a...

For an NA 944 it's not a big deal. It's just a lot of steps.

Remove axles - easy
Remove trans - easy
Remove exhaust - easy
Unbolt torque tube and pull it back - easy
Remove clutch fork pin -...
02-27-2019, 11:42 AM
Replies: 29
Views: 2,086
Posted By odonnell

There's a DIYPNP Megasquirt for the S2. It's a...

There's a DIYPNP Megasquirt for the S2. It's a bit deceptive, as it will plug right in... after you solder every last transistor and capacitor onto the motherboard. Not quite an afternoon...
02-23-2019, 05:22 PM
Replies: 29
Views: 2,086
Posted By odonnell

1) Megasquirt conversion 2) Dash refurb from...

1) Megasquirt conversion

2) Dash refurb from Classic 9

3) Front and rear euro bumpers

4) Elgin camshaft + 5* advance

5) coilovers
02-18-2019, 07:27 PM
Replies: 8
Views: 642
Posted By odonnell

Great work! Glad to see Wilson back. ...

Great work! Glad to see Wilson back.

Another killer of NA to turbo conversions is improper tuning. I'm assuming you had it dyno tuned with the new ECU? Detonation and lean AFRs will quickly...
02-17-2019, 11:02 PM
Replies: 17
Views: 1,249
Posted By odonnell

Awesome work! I need to finish mine when I'm back...

Awesome work! I need to finish mine when I'm back from working offshore. Keep us updated. I'm interested in those PCBs if you ever have them made, I mentioned it before but some friends and I are...
02-14-2019, 07:44 AM
Replies: 10
Views: 898
Posted By odonnell

Classic 9 did my early dash for $800 or so and it...

Classic 9 did my early dash for $800 or so and it looks better than new. Unfortunately I think they stopped serving the 944 community. Maybe if you asked politely...
02-12-2019, 07:27 PM
Replies: 29
Views: 4,128
Posted By odonnell

No reason it wouldn't work with a stock flywheel....

No reason it wouldn't work with a stock flywheel. However this is the reference sensor. The reason I bought the TTV flywheel is because the speed sensor is what causes problems for MS installations...
02-12-2019, 09:35 AM
Replies: 19
Views: 1,327
Posted By odonnell

I have 7J square setup on my street NA. If...

I have 7J square setup on my street NA. If anything I get oversteer more than anything due to my sway bar setup and coilover settings. It's definitely nice being able to rotate the tires. And I can...
02-11-2019, 07:24 PM
Replies: 29
Views: 4,128
Posted By odonnell

MS3Pro for my 951 in conjunction with the TTV...

MS3Pro for my 951 in conjunction with the TTV 60-2 flywheel. I may just use a stock sensor though.
02-09-2019, 11:18 PM
Replies: 29
Views: 4,128
Posted By odonnell

About $30 for the sensor and $5 for the brass...

About $30 for the sensor and $5 for the brass sleeve. And you need a M12x1.00mm tap and 5/8" drill bit. I can post details later if you want.
02-09-2019, 07:28 PM
Replies: 10
Views: 590
Posted By odonnell

The bolts should never be in a shear loading...

The bolts should never be in a shear loading condition. When torqued properly they should purely be in tension, the torque is passed via the axle flanges pressed up against the drive flanges. The...
02-09-2019, 10:57 AM
Replies: 10
Views: 590
Posted By odonnell

I think they're 12.9 bolts. I've reused them many...

I think they're 12.9 bolts. I've reused them many times but switch them out every few times. I went to 12.9 studs with grade 10 nuts on the outer flanges, makes installation a lot less messy.
02-09-2019, 06:03 AM
Replies: 29
Views: 4,128
Posted By odonnell

Hall effect sensor in place of the stock VR type....

Hall effect sensor in place of the stock VR type. Edit, Meant to post in your other thread where people were talking about what brands of sensors worked for them on VEMS.
02-04-2019, 07:20 AM
Replies: 13
Views: 853
Posted By odonnell

One of my buddies here in TX does these as well....

One of my buddies here in TX does these as well. We found the correct Oilite bushings, and the arms are welded up to add material.
01-31-2019, 11:42 PM
Replies: 26
Views: 2,583
Posted By odonnell

I also upped the heat on my soldering iron, redid...

I also upped the heat on my soldering iron, redid most of the joints and they're better (although a far cry from perfect). Thanks again for the feedback Dare, I greatly appreciate all constructive...
01-31-2019, 11:27 PM
Replies: 26
Views: 2,583
Posted By odonnell

Been super busy the last few weeks and haven't...

Been super busy the last few weeks and haven't made much progress. However, tonight I had some time and got the MS talking to my laptop. So far it's working as expected. I had a few bad jumper wires...
01-19-2019, 06:08 PM
Replies: 10
Views: 579
Posted By odonnell

If they're out of the car, replace.

If they're out of the car, replace.
01-12-2019, 05:24 PM
Replies: 15
Views: 879
Posted By odonnell

Do the underdrive pulleys really help that much?...

Do the underdrive pulleys really help that much? To me, it seemed like something I would get if I had already checked off literally everything else I could possibly do for more performance. On a...
Showing results 1 to 25 of 493
 


 
Forum Jump

Contact Us About Us Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.