Will the Brake Pad Workshop light cause the check engine light to come on?
Or is this just a coincidence? It did go out after driving the car for a few miles. If it comes back on I will take it into Porsche and have them run the diagnostic codes. Thanks SUZU |
no but the coils will. another easy job you can do yourself
|
Originally Posted by SKYSTAK
(Post 8073408)
18zl silver on 08 cs is what sine? 330 or 350?
On a Cayenne S, Your rotors will be 350x34mm for the fronts and 330x28mm for the rears. Zimmerman Coat Zs are OEM standard. |
to all, great info for the first time DIYer. i just finished the front and am starting on the rear but I have to wait until tomorrow for the triple square tools. still not sure on sizes. m16, m6, m15, t47 or t50. a bit confusing. maybe ill get them all.
the only problem w the step by step directions with pics is that at one point it says to put brake grease on pads and later on it says caution, don't put brake grease on back of pads. i left the grease off. hope i don't get brake noise. |
Originally Posted by jglennwj
(Post 8256258)
to all, great info for the first time DIYer. i just finished the front and am starting on the rear but I have to wait until tomorrow for the triple square tools. still not sure on sizes. m16, m6, m15, t47 or t50. a bit confusing. maybe ill get them all.
the only problem w the step by step directions with pics is that at one point it says to put brake grease on pads and later on it says caution, don't put brake grease on back of pads. i left the grease off. hope i don't get brake noise. No grease needed. :thumbup: |
Originally Posted by medtech
(Post 8194082)
Sorry for the late response.
On a Cayenne S, Your rotors will be 350x34mm for the fronts and 330x28mm for the rears. Zimmerman Coat Zs are OEM standard. I almost improperly bought 350mm fronts and 330 rears.... Here are the caliper colors/rotor sizes for fronts V6/Black Caliper:330mm V8/Silver Caliper:350mm V8TT/Red Caliper:350mm V8TTS/BIG Red Caliper:380mm Med tech I am going to AutohauzAZ, great cost on rotors!!! Anything above 50 bucks is shipped for free. |
I can not comment on the Zimmermann being OE -- but they do not list it as such - and they are normally accurate. I get a lot of stuff from them
The Zimmerman stuff is normally very good. I bought the whole kit from Sunset -- and the rear rotors I think are $91.00. So it is a little more with shipping. I have had such good luck with the OE stuff that I would rather not play around. Please report back about the parts -- it would be great information for the future. I know that Brembo is now making some stuff in China:nono: |
I just ordered, Zimmerman Front Drilled/Slotted, Hawk HPS for Front and Rear and Sensors
The Rotors were $241.59 shipped Front Pads $110 Rear Pads $70 All 4 sensors $40 |
Guys, just a quick check: are the 380mm TTS rotors OE from Zimmermann? If so, does anybody know the Zimmermann part #? I tried to find it, but no luck...
|
Thats a question thats been asked before I am pretty sure they are not the OEM and the dealer may be the only source
|
Originally Posted by mudman2
(Post 8353745)
Thats a question thats been asked before I am pretty sure they are not the OEM and the dealer may be the only source
|
Originally Posted by mudman2
(Post 8353242)
I just ordered, Zimmerman Front Drilled/Slotted, Hawk HPS for Front and Rear and Sensors
The Rotors were $241.59 shipped Front Pads $110 Rear Pads $70 All 4 sensors $40 rear rotors 163.30 rear pads 87.68 rear sensors 23.62 rear hardware kit 25.30 from suncoast 274.60 with free shipping..........plus 25.30...for hardware and maybe some shipping. Heres the front rotors and pads with sensors front rotors 186.14 front pads OEM 129.49 front sensors 25.10 front hardware 34.95 from suncoast. Mike, did you get 4 rotors or just front rotors, if you got 4 slotted, ping me your source for rotors please..... |
Sunset:
charges for the rear 104.67 for the pads 13.98 for each sensor 21.31 for the kit I also get the two bolts for $1.82 each Is $240 for all 4 rotors? Great Price. |
2006 CTT
Can someone confirm the calipers up front are 350mm, and rear are 330mm? (The red calipers...) Thanks! |
Are there any manufacturers that have produced stainless-steel rotors for the Pepper?
|
All times are GMT -3. The time now is 10:14 AM. |
© 2024 MH Sub I, LLC dba Internet Brands