Feeler IPD Comp Plenum and 82mm GT3 TB F/S
03-17-2016, 04:42 PM
#1
Nordschleife Master
Thread Starter
Join Date: Nov 2008
Location: Mooresville, IN (Life Long Cheesehead)
Posts: 5,815
Likes: 0
Received 55 Likes
on
36 Posts
Feeler IPD Comp Plenum and 82mm GT3 TB F/S
Yesterday I came across a X51 intake manifold mated with a GT3 throttle body. I bought it and will send my car back to FSI to install it and prep the heads. With that said I currently have an 10 month old IPD Competition plenum with a 82mm GT3 throttle body. With the X51 part I no longer need the plenum. And I won't need one of the throttle bodies.
The car goes to FSI beginning of May and will return in June. The IPD plenum and TB will be available when I get the car back. I'm not sure if the silicone hose will be available or not.
New as a package these go for around $1100-$1200 depending on where you get it.
Here is a link to the parts.
https://www.ipdplenums.com/component...era-ipd-plenum
https://www.ipdplenums.com/component...-throttle-body
Thought I would put this here 1st before it goes on the classified in June. If anyone has any interest / questions please respond here or shoot me a PM.
The car goes to FSI beginning of May and will return in June. The IPD plenum and TB will be available when I get the car back. I'm not sure if the silicone hose will be available or not.
New as a package these go for around $1100-$1200 depending on where you get it.
Here is a link to the parts.
https://www.ipdplenums.com/component...era-ipd-plenum
https://www.ipdplenums.com/component...-throttle-body
Thought I would put this here 1st before it goes on the classified in June. If anyone has any interest / questions please respond here or shoot me a PM.
03-25-2016, 05:19 PM
#3
Burning Brakes
Aw, man, did you buy the one that has the welded runners and plenum? 
I was gonna wait for my tax refund ...
Good buy, though, if you did! It had been listed for quite some time.
I was gonna wait for my tax refund ...Good buy, though, if you did! It had been listed for quite some time.
03-26-2016, 10:30 AM
#4
Nordschleife Master
Thread Starter
Join Date: Nov 2008
Location: Mooresville, IN (Life Long Cheesehead)
Posts: 5,815
Likes: 0
Received 55 Likes
on
36 Posts
Originally Posted by Lyn
I'm interested in your IPD plenum and 82mm throttle body. PM me your email address and how much you're asking and we'll see if we can come to a middle ground.
03-26-2016, 10:34 AM
#5
Nordschleife Master
Thread Starter
Join Date: Nov 2008
Location: Mooresville, IN (Life Long Cheesehead)
Posts: 5,815
Likes: 0
Received 55 Likes
on
36 Posts
Originally Posted by Carmichael
Aw, man, did you buy the one that has the welded runners and plenum? I was gonna wait for my tax refund ...
Good buy, though, if you did! It had been listed for quite some time.
I was gonna wait for my tax refund ...Good buy, though, if you did! It had been listed for quite some time.
08-03-2016, 11:35 AM
#6
Nordschleife Master
Thread Starter
Join Date: Nov 2008
Location: Mooresville, IN (Life Long Cheesehead)
Posts: 5,815
Likes: 0
Received 55 Likes
on
36 Posts
Well?.....time for an update. My car went to Flat6 end of May to get the X51 welded runner and plenum installed along with some other goodies. Jake has optimized the new setup and the car is ready. Last year when I got the car it was making 326 rwhp and 287 tq.....the car now has some more junk in the trunk and I'll post a comparison when I have the hard data.
I'm flying down to ATL tomorrow morning and grabbing a rental for the 50 minute drive to his R&D facility. My plan is to drive her home same day.....more info coming.
Here is a clip at start up from last week and a pic with my car above another RL'ster. Must have been a special on Seal Grey that day
I'm flying down to ATL tomorrow morning and grabbing a rental for the 50 minute drive to his R&D facility. My plan is to drive her home same day.....more info coming.
Here is a clip at start up from last week and a pic with my car above another RL'ster. Must have been a special on Seal Grey that day
