Notices
991 GT3 GT3RS and 911R
Sponsored by:

SOUL Performance - Custom GT3 Exhaust Tips

 
Old 02-11-2019, 05:15 PM
  #1  
Soul Performance
Basic Sponsor
Rennlist
Site Sponsor

Thread Starter
 
Soul Performance's Avatar
 
Join Date: Jun 2017
Location: Willow Grove, PA
Posts: 1,611
Likes: 0
Received 10 Likes on 9 Posts
Default SOUL Performance - Custom GT3 Exhaust Tips

Hello Everyone,

Since posting our side vs center muffler delete explanation thread, I’ve been receiving a good amount of inquiries for custom exhaust tips to replace the tip assemblies on the factory center muffler. It seemed like a no-brainer for me to get involved, and we happened to have a factory GT3 tip assembly here. We set to task and developed a replacement backing plate that is modular, giving us the ability to accommodate a variety of tip options/lengths for different models and designs, and a great deal of adjustability.
.







Options:
We have 6 different variations of standard tips to choose between based on the following styles and finishes:

Style:
Straight Cut Single Wall
Slash Cut Single Wall

Finish:
Signature Satin
Brushed
Satin Black (PVD Coating)

Pricing:
Brushed/Signature Satin: $445
Satin Black: $595

Customization:
For a setup fee of $50, we have the ability to apply custom lettering/logos. If you’d like your username, your initials, a phrase, or some relevant seven word that begins with “P”….we can do that. We can also forgo any lettering on the tips for a more factory look. This can be done immediately for the Brushed/Signature Satin finish with no additional turnaround time. That said, it has to be done before the PVD coating process on the Satin Black tips, which we send out for coating. In that event the turnaround time would be 2-4 weeks.

Fitment:
991.1 GT3 and 991.2 GT3 and RS Models

Construction:
Each backing plate is laser cut from 1/8″ thick T304L stainless steel. Each tip is hand made from .065″ thick, 4″ diameter stainless steel tubing. Mikalor Supra Heavy-Duty W4 Clamps are included to mount the tips to the backing plate.

Installation:
Swapping out tip assemblies should only take you minutes, it is attached to the center muffler by three 13mm nuts.

Continued Development:
There is an additional product I’d like to accomplish in the near future.

Resonated Turndown Tips: we are working on a set of tip assemblies that incorporates resonators into the backing plate. The end of the resonators will have a clamp to attach turndown tips that can be custom made in whatever length/angle required by the customer, and of course we’ll have some standard options for that. This will be a tip assembly you can bring with you and swap on and off in minutes in the event you need to drop some dBs at various sound restricted tracks.

These are the options I felt would fit the majority of the cosmetic goals we have for these cars. That said, I am open to discussing further options and additional customization on a case by case basis. Our PVD coater can also accommodate some unique colors (such as Blue and Gold) if you want to get super unique. We are also closely associated with Jet-Hot should you want to browse the highest quality ceramic coating options as well. Don’t hesitate to ask, I’m happy to chat about it.

Take a look at the options we have available below or on our website and let me know your thoughts. As always we appreciate your business and we’re happy to be a part of the community. If you’d like to order a set, forum members do get a discount so don’t hesitate to reach out.

Best regards,
John Gaydos
Slash Cut/Brushed Finish


.
Straight Cut/Satin Black Finish



Slash Cut/Satin Black Finish



Straight Cut/Signature Satin Finish




Satin Black Jet-Hot Ceramic Coated SOUL Center Muffler Bypass Exhaust with Satin Black PVD Finish and Custom "GT3" Logo
.
__________________
Soul Performance Products
Outstanding Exhaust Solutions, Fair Pricing, and Quality Service

John Gaydos - Performance Specialist

PCA National Instructor
Cell - (484) 883-6197
[email protected]

Mike Spock - Marketing Manager
Office (855) 486-1400

Last edited by Soul Performance; 02-20-2019 at 04:37 PM.
Soul Performance is offline  
Old 02-11-2019, 05:59 PM
  #2  
NSD991
Addict
Rennlist Member
 
NSD991's Avatar
 
Join Date: Mar 2015
Posts: 584
Received 3 Likes on 1 Post
Default

Pm sent re RS tips
NSD991 is offline  
Old 02-12-2019, 11:02 AM
  #3  
Soul Performance
Basic Sponsor
Rennlist
Site Sponsor

Thread Starter
 
Soul Performance's Avatar
 
Join Date: Jun 2017
Location: Willow Grove, PA
Posts: 1,611
Likes: 0
Received 10 Likes on 9 Posts
Default

Originally Posted by NSD991 View Post
Pm sent re RS tips
Thanks buddy! : )
__________________
Soul Performance Products
Outstanding Exhaust Solutions, Fair Pricing, and Quality Service

John Gaydos - Performance Specialist

PCA National Instructor
Cell - (484) 883-6197
[email protected]

Mike Spock - Marketing Manager
Office (855) 486-1400
Soul Performance is offline  
Old 02-12-2019, 09:01 PM
  #4  
Neb
User
 
Neb's Avatar
 
Join Date: Aug 2011
Location: Toronto, ON
Posts: 292
Likes: 0
Received 0 Likes on 0 Posts
Default

I am interested in this, do you offer this complete package? If so how much? The inlet of those tips looks narrow, how wide are they?
Originally Posted by Soul Performance View Post
Neb is offline  
Old 02-12-2019, 09:17 PM
  #5  
NSD991
Addict
Rennlist Member
 
NSD991's Avatar
 
Join Date: Mar 2015
Posts: 584
Received 3 Likes on 1 Post
Default


Here is mine. Didnĺt measure the inlet.
NSD991 is offline  
Old 02-13-2019, 12:20 PM
  #6  
Soul Performance
Basic Sponsor
Rennlist
Site Sponsor

Thread Starter
 
Soul Performance's Avatar
 
Join Date: Jun 2017
Location: Willow Grove, PA
Posts: 1,611
Likes: 0
Received 10 Likes on 9 Posts
Default

Originally Posted by Neb View Post
I am interested in this, do you offer this complete package? If so how much? The inlet of those tips looks narrow, how wide are they?
Yes we do, that exact system was custom made for a fellow Rennlist member. The breakdown is as follows. The custom satin black ceramic and PVD coating is a 2-4 week turnaround time as we have to send it out.

Center Muffler Bypass with 4in Slash Cut Tips: $895
Jet Hot Satin Black Ceramic Coating (Center Muffler): $250
PVD Satin Black Coating (Tips): $150
Custom Lettering on Exhaust Tips: $50

For your reference, our tip inlet pipes at their narrowest are 70mm. This is the same if not larger than the factory 991 GT3 tip assemblies, which I'll confirm for you in a day or so once the factory RS tips show up. For your reference, the factory 997 GT3 tip assemblies sitting on my desk neck down to approximately 62mm at the entry of the tips.
__________________
Soul Performance Products
Outstanding Exhaust Solutions, Fair Pricing, and Quality Service

John Gaydos - Performance Specialist

PCA National Instructor
Cell - (484) 883-6197
[email protected]

Mike Spock - Marketing Manager
Office (855) 486-1400
Soul Performance is offline  
Old 02-13-2019, 01:07 PM
  #7  
Soul Performance
Basic Sponsor
Rennlist
Site Sponsor

Thread Starter
 
Soul Performance's Avatar
 
Join Date: Jun 2017
Location: Willow Grove, PA
Posts: 1,611
Likes: 0
Received 10 Likes on 9 Posts
Default

To follow up on the tip piping, here is a 62mm 997 GT3 tip assembly vs our 70mm tip assembly. We use the same 70mm tip pipe diameter on our center muffler bypass.


__________________
Soul Performance Products
Outstanding Exhaust Solutions, Fair Pricing, and Quality Service

John Gaydos - Performance Specialist

PCA National Instructor
Cell - (484) 883-6197
[email protected]

Mike Spock - Marketing Manager
Office (855) 486-1400
Soul Performance is offline  
Old 02-20-2019, 02:41 PM
  #8  
Soul Performance
Basic Sponsor
Rennlist
Site Sponsor

Thread Starter
 
Soul Performance's Avatar
 
Join Date: Jun 2017
Location: Willow Grove, PA
Posts: 1,611
Likes: 0
Received 10 Likes on 9 Posts
Default

A few fellows reached out that needed to drop DB at some autocross events for SCCA and we were happy to oblige and develop these resonated turndown tips. They take minutes to install as it's simply three nuts holding on the factory tip assembly. The turndown tips themselves use vband clamps and are quickly and easily loosened/adjusted to face whichever direction you’d like. Videos and DB testing to come as they begin to make their way to our customers that requested we tackle this project.


__________________
Soul Performance Products
Outstanding Exhaust Solutions, Fair Pricing, and Quality Service

John Gaydos - Performance Specialist

PCA National Instructor
Cell - (484) 883-6197
[email protected]

Mike Spock - Marketing Manager
Office (855) 486-1400

Last edited by Soul Performance; 02-20-2019 at 04:30 PM.
Soul Performance is offline  
Old 02-24-2019, 10:00 AM
  #9  
TRAKCAR
Addict
Rennlist Member
 
TRAKCAR's Avatar
 
Join Date: Jan 2008
Location: S. Florida
Posts: 27,307
Received 25 Likes on 19 Posts
Default

Sign me up!
TRAKCAR is offline  
Old 02-27-2019, 11:50 PM
  #10  
NSD991
Addict
Rennlist Member
 
NSD991's Avatar
 
Join Date: Mar 2015
Posts: 584
Received 3 Likes on 1 Post
Default


Thank you John

Nicely packaged

Black tips

Slash cut
NSD991 is offline  
Old 02-28-2019, 11:00 AM
  #11  
Soul Performance
Basic Sponsor
Rennlist
Site Sponsor

Thread Starter
 
Soul Performance's Avatar
 
Join Date: Jun 2017
Location: Willow Grove, PA
Posts: 1,611
Likes: 0
Received 10 Likes on 9 Posts
Default

Originally Posted by NSD991 View Post

Thank you John

Nicely packaged

Black tips

Slash cut
Thanks for the loan of the RS tip assembly, it was much appreciated : ) I checked those tips quite carefully before they were packaged, but it looks like you have a mark on that one you posted. If that doesn't clean up, let me know I'll send you another
__________________
Soul Performance Products
Outstanding Exhaust Solutions, Fair Pricing, and Quality Service

John Gaydos - Performance Specialist

PCA National Instructor
Cell - (484) 883-6197
[email protected]

Mike Spock - Marketing Manager
Office (855) 486-1400
Soul Performance is offline  
Old 02-28-2019, 11:51 AM
  #12  
yxc145
User
 
Join Date: Mar 2013
Location: Chicago, Taiwan
Posts: 230
Likes: 0
Received 0 Likes on 0 Posts
Default

I got the SOUL center bypass set up with black tips. Can't wait for the weather to warm up to install it.
yxc145 is offline  
Old 02-28-2019, 02:57 PM
  #13  
NSD991
Addict
Rennlist Member
 
NSD991's Avatar
 
Join Date: Mar 2015
Posts: 584
Received 3 Likes on 1 Post
Default

Originally Posted by Soul Performance View Post
Thanks for the loan of the RS tip assembly, it was much appreciated : ) I checked those tips quite carefully before they were packaged, but it looks like you have a mark on that one you posted. If that doesn't clean up, let me know I'll send you another
JOHN, NO NEED, THEY ARE PERFECT!
Thanks again
NSD991 is offline  
Old 03-01-2019, 08:48 PM
  #14  
NSD991
Addict
Rennlist Member
 
NSD991's Avatar
 
Join Date: Mar 2015
Posts: 584
Received 3 Likes on 1 Post
Default






Much better
NSD991 is offline  
Old 03-13-2019, 11:28 AM
  #15  
Soul Performance
Basic Sponsor
Rennlist
Site Sponsor

Thread Starter
 
Soul Performance's Avatar
 
Join Date: Jun 2017
Location: Willow Grove, PA
Posts: 1,611
Likes: 0
Received 10 Likes on 9 Posts
Default

Originally Posted by NSD991 View Post

Much better
Looking good! Love the black on that car : )
__________________
Soul Performance Products
Outstanding Exhaust Solutions, Fair Pricing, and Quality Service

John Gaydos - Performance Specialist

PCA National Instructor
Cell - (484) 883-6197
[email protected]

Mike Spock - Marketing Manager
Office (855) 486-1400
Soul Performance is offline  

Thread Tools
Search this Thread

Contact Us - About Us - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: