Post Your Stripes/Vinyl - Official 991 GT Car Stripes and Vinyl Database
#136
Rennlist Member
I want to kick off the discussion with something I have been noticing when it comes to 911 R side stripe kits. We have provided design and consulting services for over 50 911 R side stripe vinyl kits. In a typical 911 R side stripe kit design we will create a series of renderings to help select the general colors for the main stripe and the "PORSCHE" lettering. The next step then is to help the client decide whether or not the stripes will be done via CXX, or an aftermarket company.
Doing the stripes via CXX adds a perceived value to the car, and assures the stripes will be properly fitted, and of course appear as OEM as possible. When done from the factory, the 911 R side stripes are cut, trimmed, and fit in a very specific fashion (though this isn't to say sometimes the factory gets a vinyl color wrong, or install technique varies from vehicle to vehicle). When it comes to aftermarket 911 R side stripe kits, typically a lot of faith is placed in the installer to reference photos online of an OEM kit to assure everything is fit properly. It is important to note that even if an installer masters the fitting, it is still possible the actual vinyl kit purchased by the client is using the incorrect version of the "PORSCHE" logo, has the logo centered incorrectly, or has incorrect stripe dimensions.
Here is an example showing the characteristics of an OEM 911 R style side stripe:
You will note:
Now, this isn't to say any aftermarket kit that isn't installed to OEM CXX specifications is "wrong"- but we just wanted to detail these nuances for members that are as OCD as we are about these things!
Some owners see vinyl as a cheap, quick, and easy way to change up the look of the car, and that is fine. There are plenty of cost effective options out there for changing up the look. We have some clients that swap out stripe kits on a bi-yearly basis. However, if you are an owner that is concerned with having the most factory possible fit and finish on your striping kit and intend on leaving it on for a long time, we think it is extremely important that a certain criteria is met with the production and installation of the vinyl.
Feel free to ask any specific questions about choosing the correct stripe kit for you in this thread or shoot us a message and we'd love to chat!
Doing the stripes via CXX adds a perceived value to the car, and assures the stripes will be properly fitted, and of course appear as OEM as possible. When done from the factory, the 911 R side stripes are cut, trimmed, and fit in a very specific fashion (though this isn't to say sometimes the factory gets a vinyl color wrong, or install technique varies from vehicle to vehicle). When it comes to aftermarket 911 R side stripe kits, typically a lot of faith is placed in the installer to reference photos online of an OEM kit to assure everything is fit properly. It is important to note that even if an installer masters the fitting, it is still possible the actual vinyl kit purchased by the client is using the incorrect version of the "PORSCHE" logo, has the logo centered incorrectly, or has incorrect stripe dimensions.
Here is an example showing the characteristics of an OEM 911 R style side stripe:
You will note:
- The stripes DO NOT wrap around into either of the wheel wells. They are actually trimmed short. Doing this saves the leading edge of the vinyl from excessive stone chips that could potentially destroy the portion of the stripe on the fender or rear quarter panel. When the stripes are wrapped around into the wheel wells this is the easiest way to tell it is a non-OEM stripe kit.
- The stripes also DO NOT wrap fully around the edges of the door. I have noticed though that some 991.2 CXX cars DO have the vinyl wrapped around the edges. So I think this portion of the install at Porsche is usually dependent upon the installer at CXX.
- The "PORSCHE" logo is centered in reference to the door
- The rake of the stripe follows the rake of the door's lower shutline, rather than being ground level. I have found this to vary between some CXX kits and 911 R's however though following the rake of the door is most common.
Now, this isn't to say any aftermarket kit that isn't installed to OEM CXX specifications is "wrong"- but we just wanted to detail these nuances for members that are as OCD as we are about these things!
Some owners see vinyl as a cheap, quick, and easy way to change up the look of the car, and that is fine. There are plenty of cost effective options out there for changing up the look. We have some clients that swap out stripe kits on a bi-yearly basis. However, if you are an owner that is concerned with having the most factory possible fit and finish on your striping kit and intend on leaving it on for a long time, we think it is extremely important that a certain criteria is met with the production and installation of the vinyl.
Feel free to ask any specific questions about choosing the correct stripe kit for you in this thread or shoot us a message and we'd love to chat!
Sam
#137
Rennlist Member
Installed this on my buddy's GT3RS the other day. Now I need to come up with something for my car.
#138
Rennlist Member
#139
Rennlist Member
Need your opinions on which stripe looks better on my Graphite Blue Touring Just installed them and trying to decide which I like best. Raining outside today so not great pictures.
Sam
Silver stripe with Black Logo
Matt Black stripe with Yellow Logo
Sam
Silver stripe with Black Logo
Matt Black stripe with Yellow Logo
#141
My 2c.
#142
#143
i like the yellow. Little bit of color in a sad blue black and silver world.
#144
#147
Three Wheelin'
IROC stripe.
#148
Rennlist Member
#149
Three Wheelin'
#150
Rennlist Member
Brewster Green
Needing some TLC