Random 964 VIDEO thread...
#76
Rennlist Member
Spoiler: Like the 997 TT driver really had to jump the line?
Nice RWB style
Not all show, yes these guys track.
Nice RWB style
Not all show, yes these guys track.
Last edited by 911Jetta; 01-05-2013 at 12:23 AM.
#77
Rennlist Member
Holly moly!
Holly flares! Holly wheels! Holly stance! Holly sans gutter rails! Holly single aero mirror! Holly door sils! Holly white interior! Holly White Knight!
Holly moly!
OK, not a true 964 based on the tail lights alone, but still.
Needs a dual exhaust or a "Kai" center mount exhaust. Maybe a duck too?
Talk amongst yourselves...
Holly flares! Holly wheels! Holly stance! Holly sans gutter rails! Holly single aero mirror! Holly door sils! Holly white interior! Holly White Knight!
Holly moly!
OK, not a true 964 based on the tail lights alone, but still.
Needs a dual exhaust or a "Kai" center mount exhaust. Maybe a duck too?
Talk amongst yourselves...
#78
Rennlist Member
Lumpy. Love the wheels.
#79
Rennlist Member
Porsche Carrera RS (964) - Porsche Center Stuttgart
#80
Rennlist Member
sounding good!
#82
Drifting
Thread Starter
#83
Race Car
thanks Frank - will get to editing something 'freer' later ... stumbled on this ..red 964 rs drive
(apologies if posted already)
(apologies if posted already)
Last edited by HiWind; 01-07-2013 at 01:43 AM.
#84
Race Car
here you go - thought it time to find a way around the wind noise for my vids - which I really enjoy/need when the car is away/on jacks!
so I bought a simple head phone jack (mono),
4m of monostrand wire, (that's mono wire but 2 strands)
a little mic ($2)
and some carpet foam - in total about $5s worth for everything.
Solder the ends up ie mic and jack,
drill an appropriate sized hole in the gopro case - can plug with a grommet plug if not in use
start with a tiny one until you're 100% sure you're on the spot for the mic input hole when the camera is fully seated
Also the last 3mm (in width terms ie as you're widening) shd be drilled with a countersink tool
this way you can make sure the hole is very tight on the jack - wlll be exposed to high speed external bufffeting)
and then mount the camera on the bonnet,
running the cable to the back via roof rain channel with a couple little slots of insulation tape to secure.
I put the well wrapped mic (carpet foam) through the clips for the air intake to hold it secure ... but got too much whoosh!
... so dropped the mic down the heater pipe output (mine isn't operational) so its suspended just above the left exhaust
Voila....
so I bought a simple head phone jack (mono),
4m of monostrand wire, (that's mono wire but 2 strands)
a little mic ($2)
and some carpet foam - in total about $5s worth for everything.
Solder the ends up ie mic and jack,
drill an appropriate sized hole in the gopro case - can plug with a grommet plug if not in use
start with a tiny one until you're 100% sure you're on the spot for the mic input hole when the camera is fully seated
Also the last 3mm (in width terms ie as you're widening) shd be drilled with a countersink tool
this way you can make sure the hole is very tight on the jack - wlll be exposed to high speed external bufffeting)
and then mount the camera on the bonnet,
running the cable to the back via roof rain channel with a couple little slots of insulation tape to secure.
I put the well wrapped mic (carpet foam) through the clips for the air intake to hold it secure ... but got too much whoosh!
... so dropped the mic down the heater pipe output (mine isn't operational) so its suspended just above the left exhaust
Voila....
Last edited by HiWind; 01-11-2013 at 04:42 PM. Reason: Clarification re wire
#85
Drifting
Thread Starter
964 featured briefly -
Last edited by Porsche964FP; 01-09-2013 at 12:18 PM.
#86
Race Car
won't be long Frank - the last few days are the worst!
And all that power on tap, and the awesome process of bedding (note!) it in will be worth it
And all that power on tap, and the awesome process of bedding (note!) it in will be worth it
#88
Rennlist Member
^^^^^ Love watching the rear suspension move through its travel. Bonus for having gold rims!
December track day at VIR
For those of you with relatively little track experience like me (with only 6 DEs under my belt), this is a great video to see what a typical track session with an instructor is like. Eric, my instructor, is a great guy and really helped me through a couple corners that I kept messing up...you'll hear him say, "faster...it'll hold!".
December track day at VIR
For those of you with relatively little track experience like me (with only 6 DEs under my belt), this is a great video to see what a typical track session with an instructor is like. Eric, my instructor, is a great guy and really helped me through a couple corners that I kept messing up...you'll hear him say, "faster...it'll hold!".