Cup Car SPG mounting details
#31
Addict
Rennlist Member
Rennlist Member
Join Date: Apr 2002
Location: Apex, NC
Posts: 2,426
Likes: 0
Received 0 Likes
on
0 Posts
Pictures of the motorsports side mounts (drivers side, L brackets)
i am assuming i have them on correctly - i will fit them to the car later thsi week hopefully
i am assuming i have them on correctly - i will fit them to the car later thsi week hopefully
#33
Addict
Rennlist Member
Rennlist Member
Join Date: Apr 2002
Location: Apex, NC
Posts: 2,426
Likes: 0
Received 0 Likes
on
0 Posts
great - it seems the logical way to put it together, bob. For the passanger side i have the Normal Recaro side mounts which position it in the center of the seat mounting brackets.
Did they make a right hand set (i would assume so for European customers) but......
i am going to switch out the stock seats for the recars for the parade (i think) it will be a punishing ride down there in June.
Did they make a right hand set (i would assume so for European customers) but......
i am going to switch out the stock seats for the recars for the parade (i think) it will be a punishing ride down there in June.
#34
Rennlist Member
You are right, I had a brain Frt, you can't reverse the mounts for the passenger side; the seat would have to be positioned to the right on that side.
To my knowledge the seat was only made to go on the drivers side as delivered by Porsche. When I've been in Germany and looked at an M003 Clubsport RS, which had the race seat on both sides, I didn't notice how the side plates were oriented, or what plates were used, on the passenger side.
I bet the seat and the mounts are the same in an M003 and the driver is to the center and the passenger is to the right.
To my knowledge the seat was only made to go on the drivers side as delivered by Porsche. When I've been in Germany and looked at an M003 Clubsport RS, which had the race seat on both sides, I didn't notice how the side plates were oriented, or what plates were used, on the passenger side.
I bet the seat and the mounts are the same in an M003 and the driver is to the center and the passenger is to the right.
#36
Addict
Rennlist Member
Rennlist Member
Join Date: Apr 2002
Location: Apex, NC
Posts: 2,426
Likes: 0
Received 0 Likes
on
0 Posts
Installed in the Car..
A couple of notes...
1. You cannot use these with the stock seat belts - there is not enough room in between the center console and the seat once it is relocated. so only 5-6pt belts will work.
2. this moves the seat 2" to the center of the car - it feels better.
A couple of notes...
1. You cannot use these with the stock seat belts - there is not enough room in between the center console and the seat once it is relocated. so only 5-6pt belts will work.
2. this moves the seat 2" to the center of the car - it feels better.
#37
Drifting
Thread Starter
Marc,
Which B-K part # are you referring to? R9062?
I just ordered a set for the drivers side just to see if that works, since I don't have access to the factory mounts.
http://www.livermoreperformance.com/...at_mounts.html
Which B-K part # are you referring to? R9062?
I just ordered a set for the drivers side just to see if that works, since I don't have access to the factory mounts.
http://www.livermoreperformance.com/...at_mounts.html
Originally Posted by Marc Shaw
That is exactly the same as the B-K mounts I have - they move the seat about 1/2" closer to the centre tunnel.
Marc
Marc
#38
Addict
Rennlist Member
Rennlist Member
I recently installed a SPG XL Pro Racer using the Recaro mounts and sliders. I had holes drilled lower than the normal Recaro holes in order to lower the seat a bit and get the angle to what was desired.
Kenny: Griffin Motorwerks in Berkley has the brackets (it's where I got my seat and brackets).
Kenny: Griffin Motorwerks in Berkley has the brackets (it's where I got my seat and brackets).
#39
Rennlist Member
Join Date: Nov 2005
Location: Montreal, Canada
Posts: 3,854
Likes: 0
Received 0 Likes
on
0 Posts
Now it all makes sence, I knew my seat was off centered but couldn't figure what to do to remedy(since both sides are flared). Maybe we could do the same (like in Cupcar's picture) with the brey krause mounts R9062 (reverse one side) since the base plate is sloted. Kgorman, was that your plan??
#40
Drifting
Thread Starter
Thats the plan, yeap. I will post pics if it works out.
Originally Posted by CWay27
Now it all makes sence, I knew my seat was off centered but couldn't figure what to do to remedy(since both sides are flared). Maybe we could do the same (like in Cupcar's picture) with the brey krause mounts R9062 (reverse one side) since the base plate is sloted. Kgorman, was that your plan??
#41
Super Duper Moderator
Lifetime Rennlist
Member
Lifetime Rennlist
Member
Originally Posted by kgorman
Marc,
Which B-K part # are you referring to? R9062?
Which B-K part # are you referring to? R9062?
Marc
#43
Super Duper Moderator
Lifetime Rennlist
Member
Lifetime Rennlist
Member
Originally Posted by kgorman
Thanks Marc. Any news?
Marc
Last edited by Marc Shaw; 08-03-2007 at 01:28 PM.