napa heat control valve
#1
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
has anyone used auto store heat control valve with satisfactory results?connected mine to direct vacumme to keep it closed.the valve did operate so i'm assuming it's leakin through as i'm still getting heat.thanks
#2
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
No problems after two years with Napa P/N 6601410
![](https://partimages.genpt.com/thumbs/395143.jpg)
May consider the plastic version Napa P/N 6601230
![](https://partimages.genpt.com/thumbs/395121.jpg)
Napa P/N 6601410 used to be this:
![](http://www.928motorsports.com/parts/images/heatervalve/heatervalve.jpg)
But is nowhere to be found at Napa (based on my limited research)
However, it is available from Carl: http://www.928motorsports.com/parts/heatervalve.php
I've used this one and is the one I prefer.
![](https://partimages.genpt.com/thumbs/395143.jpg)
May consider the plastic version Napa P/N 6601230
![](https://partimages.genpt.com/thumbs/395121.jpg)
Napa P/N 6601410 used to be this:
![](http://www.928motorsports.com/parts/images/heatervalve/heatervalve.jpg)
But is nowhere to be found at Napa (based on my limited research)
However, it is available from Carl: http://www.928motorsports.com/parts/heatervalve.php
I've used this one and is the one I prefer.
Last edited by Jadz928; 05-02-2011 at 11:29 AM.
#4
Burning Brakes
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I used the plastic one. I think it was 13.00 or 14.00 . If I had it to do over, I would use the metal. The plastic one will also require that you sand down the seams from the mold. Easy to do, but for the price difference go with the metal.
#5
Three Wheelin'
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Yeah i was considering the metal unit (the reason i know what it cost). For now,mine just began working again. I had mine wire tied all last summer. During the winter i cut the wire tie for heat. I just tried it a few days ago when it was warm and not raining. AC was COLD. I am sure its going to fail soon. Probably in a blazing hot day. LOL
#6
Team Owner
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I would suggest to use a new factory HCV and short hose....... that is all!
Last edited by Mrmerlin; 05-02-2011 at 10:48 PM.
#7
Supercharged
Rennlist Member
Rennlist Member
Join Date: May 2002
Location: Back in Michigan - Full time!
Posts: 18,925
Likes: 0
Received 61 Likes
on
35 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I tried that exact one (the one shown above that's being sold by 928 MS) and it lasted about 6 weeks. ![Frown](https://rennlist.com/forums/images/smilies/frown.gif)
Went back to the Porsche unit. Going on 3 years so far.
![Frown](https://rennlist.com/forums/images/smilies/frown.gif)
Went back to the Porsche unit. Going on 3 years so far.
Trending Topics
#8
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Which one caused you issues? How did it fail?
#11
Supercharged
Rennlist Member
Rennlist Member
Join Date: May 2002
Location: Back in Michigan - Full time!
Posts: 18,925
Likes: 0
Received 61 Likes
on
35 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
The last one you pictured (Gold and Black). I was having heat all the time, everything seemed to move properly, so either the seal or the plate gave way.
I do have one of the all silver one's you posted waiting in the wings for when the Porsche valve dies.
I do have one of the all silver one's you posted waiting in the wings for when the Porsche valve dies.
#12
Rennlist Member
#13
Team Owner
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Jim the reason for what i posted the Porsche valve is a great break in the chain if you replace it on a regular basis it wont fail.
that said if there is a problem with the cooling system this would be where you would want it to fail as its at the top of the engine and thus you wont loose all of the coolant if the short hose or the valve itself fails.
That said if your valve is older than 5 YO it is wise to inspect it and replace it if its not functioning correctly
in this case less is more,
I wont install any other valve on any customers car
that said if there is a problem with the cooling system this would be where you would want it to fail as its at the top of the engine and thus you wont loose all of the coolant if the short hose or the valve itself fails.
That said if your valve is older than 5 YO it is wise to inspect it and replace it if its not functioning correctly
in this case less is more,
I wont install any other valve on any customers car
#14
Addict
Rennlist Member
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I have used the top metal one and a metal version of the 928MS part with good effect. I am not a fan of the Porsche part because they have been known to crack and dump all the coolant on some cars. On the 968 and 944S2 they are right by the RF tire so that can get interesting. On these cars they also get hotter as they are right by the exhaust header so this might be less of a problem on the 928.
The Porsche ones I have only seen fail internally (leaking hot water or leaking vacuum) but I have had zero problems with the alternative metal replacements thus far.
The Porsche part is cheap so it's not a big deal to replace it every 10-15 years. Mine failed at 15 years, 100k miles.
Concur on replacing the stub hose.
Cheers,
-Joel.
The Porsche ones I have only seen fail internally (leaking hot water or leaking vacuum) but I have had zero problems with the alternative metal replacements thus far.
The Porsche part is cheap so it's not a big deal to replace it every 10-15 years. Mine failed at 15 years, 100k miles.
Concur on replacing the stub hose.
Cheers,
-Joel.
#15
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Jim the reason for what i posted the Porsche valve is a great break in the chain if you replace it on a regular basis it wont fail.
that said if there is a problem with the cooling system this would be where you would want it to fail as its at the top of the engine and thus you wont loose all of the coolant if the short hose or the valve itself fails.
That said if your valve is older than 5 YO it is wise to inspect it and replace it if its not functioning correctly
in this case less is more,
I wont install any other valve on any customers car
that said if there is a problem with the cooling system this would be where you would want it to fail as its at the top of the engine and thus you wont loose all of the coolant if the short hose or the valve itself fails.
That said if your valve is older than 5 YO it is wise to inspect it and replace it if its not functioning correctly
in this case less is more,
I wont install any other valve on any customers car
You've piqued my curiosity, as it's clear you've thought this thru.
What is the next weakest link you are preserving? What give's next?