993 Rebuild & More
03-27-2016, 11:35 PM
AddictRennlist Member
Join Date: Aug 2002
Posts: 403
Likes: 0
Congrats on your build, have you discussed up grading the camshaft to 993RS with Steve?
04-07-2016, 03:32 PM
Rennlist Member
Thread Starter
Join Date: Nov 2011
Location: Saskatoon SK Canada
Posts: 805
Quote:
Originally Posted by
0396
Congrats on your build, have you discussed up grading the camshaft to 993RS with Steve?
Im keeping everything on the motor stock
04-07-2016, 03:41 PM
Rennlist Member
Thread Starter
Join Date: Nov 2011
Location: Saskatoon SK Canada
Posts: 805
Rear axle CV parts and clutch/fork stuff
Attached Images
04-07-2016, 03:45 PM
Rennlist Member
Thread Starter
Join Date: Nov 2011
Location: Saskatoon SK Canada
Posts: 805
oil cooler is clean out and back on
cleaning up the from end, found one ripped tie rod, i guess I replace both
Getting ready to install the BBS 10 shocks
04-07-2016, 03:48 PM
Rennlist Member
Thread Starter
Join Date: Nov 2011
Location: Saskatoon SK Canada
Posts: 805
04-07-2016, 03:53 PM
Drifting
Join Date: Apr 2013
Location: Nothern NJ
Posts: 2,286
Replace the inner tie rods while you are at it. The ball joints inside of them wear out and intoduce play.
04-07-2016, 06:36 PM
RL Technical Advisor
Join Date: May 2001
Location: Portland Oregon
Posts: 11,871
Likes: 0
Quote:
Originally Posted by
NYC993
Replace the inner tie rods while you are at it. The ball joints inside of them wear out and intoduce play.
Yesssss! The inners are rubber and they deteriorate over time.
04-08-2016, 10:17 AM
Rennlist Member
Thread Starter
Join Date: Nov 2011
Location: Saskatoon SK Canada
Posts: 805
Yes my plan was to replace the whole tie rod including inner
getting the inner bolt off seems to be very difficult
Last edited by Enso; 04-08-2016 at 10:38 AM .
04-08-2016, 10:20 AM
Rennlist Member
Thread Starter
Join Date: Nov 2011
Location: Saskatoon SK Canada
Posts: 805
Removing the rear axles, cleaning and cleaning
getting ready to repack the CV bearings
04-08-2016, 10:23 AM
Rennlist Member
Thread Starter
Join Date: Nov 2011
Location: Saskatoon SK Canada
Posts: 805
Just waiting for the Swepco 101 grease to arrive
Attached Images
04-10-2016, 03:21 PM
Rennlist Member
Thread Starter
Join Date: Nov 2011
Location: Saskatoon SK Canada
Posts: 805
Quote:
Originally Posted by
Steve Weiner-Rennsport Systems
Yesssss! The inners are rubber and they deteriorate over time.
Yes i will do this too, thanks for the reminder guys!
04-11-2016, 02:35 PM
Racer
Join Date: Apr 2008
Location: Northeast
Posts: 347
Likes: 0
Boy you're not messing around!
Keep up the good work.
05-06-2016, 10:32 PM
AddictRennlist Member
Join Date: Aug 2002
Posts: 403
Likes: 0
Good day, any further updates?
05-08-2016, 01:06 PM
Rennlist Member
Thread Starter
Join Date: Nov 2011
Location: Saskatoon SK Canada
Posts: 805
Drive shafts complete and going back on
i also check the wheel sensors for ohms and give them a spin on the wheel checking the AC output at the same time...all good
05-08-2016, 01:08 PM
Rennlist Member
Thread Starter
Join Date: Nov 2011
Location: Saskatoon SK Canada
Posts: 805
More treats!....Struts & tiered ends came in from Steve Weiner
Attached Images