Identifying Durametric software fault codes?
02-26-2008, 06:21 PM
#1
Rennlist Member
Thread Starter
Identifying Durametric software fault codes?
I just ran the Durametric software on my 06 997 C4S and got the following faults:
Airbag: C152 Meldung timeout PSM
PAS: 8004 Versorgungsspannung Klemme 50 (SC+)
Does anyone know what these mean and is there a list of fault codes I can get?
Thanks in advance.
Airbag: C152 Meldung timeout PSM
PAS: 8004 Versorgungsspannung Klemme 50 (SC+)
Does anyone know what these mean and is there a list of fault codes I can get?
Thanks in advance.
02-27-2008, 11:16 PM
#6
Three Wheelin'
Join Date: Dec 2005
Location: Norwalk,CT
Posts: 1,853
Likes: 0
Received 0 Likes
on
0 Posts
What has Durametric have to say about these issues?
You may have the latest software, but obviously, there is some issue which they need to be aware of.
Deanski
You may have the latest software, but obviously, there is some issue which they need to be aware of.
Deanski
02-28-2008, 12:01 PM
#7
Rennlist Member
Shouldn't be errors in German. Do you by chance have German set as your PCM language?
If you join Renntech.org you'll have access to Porsche error codes; however, I've had a few error codes come up with Durametric that I could not find on Renntech's database! The car runs perfectly and there were no flags at my recent 2-year service at Ira (although they would not provide me with a DME printout).
If you join Renntech.org you'll have access to Porsche error codes; however, I've had a few error codes come up with Durametric that I could not find on Renntech's database! The car runs perfectly and there were no flags at my recent 2-year service at Ira (although they would not provide me with a DME printout).
Trending Topics
02-28-2008, 04:37 PM
#12
Rennlist Member
Thread Starter
Just received this from Durametric,
I Had PSE installed by the local Porsce dealer and I know they did disconnect the battery so that is probable the cause of these. I will reset them and monitor. Thanks everyone who responded.
--------------------------------------------------------------------------------------------------------
The software is capable of displaying approximately 8500 fault codes, and there are about 8250 in English so some faults will default to German when the English description is not available. Most of these are for the 997 as these being new the documentation from Porsche comes out first in German.
Both of these faults are in German.
PAS: 8004 Versorgungsspannung Klemme 50 (SC+)
This fault means “Supply voltage at terminal 50” this was probably caused by a disconnected battery.
And
C152 Meldung timeout PSM
“Communications timeout with PSM”, another fault that is normally caused by disconnecting the battery.
I have added both of these to the English list so the next release will include the updated descriptions.
Best Regards,
Duram
Durametric Software
I Had PSE installed by the local Porsce dealer and I know they did disconnect the battery so that is probable the cause of these. I will reset them and monitor. Thanks everyone who responded.
--------------------------------------------------------------------------------------------------------
The software is capable of displaying approximately 8500 fault codes, and there are about 8250 in English so some faults will default to German when the English description is not available. Most of these are for the 997 as these being new the documentation from Porsche comes out first in German.
Both of these faults are in German.
PAS: 8004 Versorgungsspannung Klemme 50 (SC+)
This fault means “Supply voltage at terminal 50” this was probably caused by a disconnected battery.
And
C152 Meldung timeout PSM
“Communications timeout with PSM”, another fault that is normally caused by disconnecting the battery.
I have added both of these to the English list so the next release will include the updated descriptions.
Best Regards,
Duram
Durametric Software
